Free CCNA | CDP & LLDP | Day 36 | CCNA 200-301 Complete Course

Why learn all the "show" commands by heart? You just need to know the logic of action. The router will tell you the rest after entering "show cdp?" It does not make sense

tysm

we still haven't found the "channel failed to load" guy.

Boson practice exam question is kind of tricky for me😅 Since I am thinking of neighbors output along with detail.

Hi Jeremy, how are you?
So into a network without Cisco devices, I enable LLDP on R1 and LLDP will start working on the whole network ? Thanks

👌🏾👌🏾👌🏾👌🏾

Great content!

hey Jeremy, Thanks so much for this video and all the other videos as well. I think this must be the easiest topic on entire CCNA. So good to have an easy topic after learning OSPF, IPv6, ACL.😀

How to run wireshark on router or switch to capture such packets?

I have question regarding remembering multicast MAC addresses , do we need to remember it for the sake of exam or is it useful to remember it otherwise also?

this is very helpful and very good, thank Jeremy very much for the hard work.

We must atleast like and subscriber to thank Jeremy for the intelligent and hardwork he has done

0100.0ccc.cccc = cccccccccdp's multicast mac

what is multicast mac means? pls anyone help. tnqs

they should remove the dislike button from your channel man !!! THANK YOU

thank you

Hello Jeremy, thanks for this very helpful course, is there any chance to have CCNP as well?

So many MAC addresses to memorize..

if you count the syllables of CDP then you can remember that cdp timers are divisible by 3. for example, CDP has 3 syllables, the timers are 180 hold timer divided by 60 second update timer = 3. The same goes for LLDP, LLDP has 4 syllables in the acronym, and timers are 120 divided by 30 = 4! Easy way to remember hold & update timers for both protocols.

Jeremy courses are the best, don't skip the ads, let's help somehow!

can lldp transmit and receive be shown in the running-config and the lldp run is not active

Jeremy is a legend

hey,I didn't get the email with flashcard deck. Do I have enroll in any of courses for that ?

most boring topic so far

Hey. Any thoughts on dividing this video in chapters?

thank you
🟢

very good, thanks Jeremy for the hard work.

Very good explanation .easy to understand

Today we start with a relaxed topic after the deepness of IPv6 and ACLs. Hope NTP will be also "easy" like this.^^

best

started from day 1 and now I am here. Learned a lot along the way. Thank you for the time you have invested in the production of these videos. I have 2 questions:
* Are you planning to start a series on CCNP? Meanwhile can you please guide me to some good CCNP resources?
* Currently this series has videos till day 51. How many days are yet to go? and do you have any paid ccna || ccnp course?

Who Disliked the Video, they thought its a download button there !

Jeremy sounds like every Anti-vaxxer outthere - DO YOUR OWN RESEARCH!!!! JK, please continue with your awesome course! <3

Hi Jeremy,
Hope you doing fine

You mentioned that CDP/LLDP are often not used.
What are main reasons an engineer/administrator would use them?

Enable the LLDP/CDP globally means, to enable the protocol on all interfaces of the device at once ???- right jeremy?
or do we have to enable the protocol on each interface manually after applying command # cdp/lldp run

Great quiz questions to make viewers think and further understand the material. Thank you.

hello!
if cdp is a layer 2 protocol than why "show cdp traffic" command shows "packets" and not "frames"?

thank you

if i try to check show lldp interface it say invalid command

Ahhhhh Another day un bikini bottom, taking a masterclass with jeremy, jeremy, did i tell u that i wanna send u a burguer by uber eats??, well, now, I wanna send u two, haha, thank u boss!!

Thank you for your effort

How many more videos are there in total for the course?

You are the man! Thanks so much for your course

could we disable cdp globally and enable it on the interface ? thx for u r efforts sir and God bless u