Комментарии:
I want to make a RC car with this. How can i make it?
Ответитьwhats the distance range?
ОтветитьI have a problem. So, i built it but the receiver output is 4V. When I hold the button it drops to 1V for a second and then back to 4V. Any help?
ОтветитьWith these connections, is the receiver output suitable for driving a MOC3021? Thanks for your reply!
ОтветитьHello sir....i want to buy 100 piece...
Ответитьso you can send morse with the RF433 wow
ОтветитьHello it's not working
ОтветитьIF we have 2 transmitters A n B 433Mhz. Can either of them able to send signal if both Tx are on?
IF can't transmit signal, so what IC should I use when I've more than 1 project / 1 Tx ON together ?
What reach does it have
ОтветитьQue alcance tiene
ОтветитьWhat are you using to connect them
ОтветитьHi good day… can I use this for tail light.?
ОтветитьCan we use a motor insted of led
ОтветитьCan to mode togle
Ответитьwhat is the range
ОтветитьSir i do same like you but it does not work & I use only 1.5V cell or battery
Ответитьmy only question is if I replaced the light with a wire would electricity come out for that split second, and could that turn on something else, for example a motor. Also thank you, I have been searching the internet for days and I finally found the perfect video (if you are wonder, that is your video)
Ответитьkisi ko 1 metar bolrahe ho kisiko 10 metar bol rahe ho kisiko 5 metar bol rahe ho.i think your confuse you did not properly work on this project .
ОтветитьTrasmitor range?
ОтветитьDear friend
What is the maximum work distance?
Thanks!
Querido amigo,
en este video que muestras, ¿qué distancia máxima se puede alcanzar entre emisor y receptor?
gracias
Can I use lead acid battery instead of mobile battery
ОтветитьHi, can I use a buzzer in the place of led? I want it to be like a remote when pressed, the reciever makes a sound
ОтветитьPlease how meter range work
ОтветитьPlease 4 channel module make video upload bro
ОтветитьHow to fit this kit on drone
ОтветитьVery good video. it worked for me. Initially i used 9v. It did not work. Tried with 5v, it worked fine. Thank you.
Just to get clarification.
In this video, as per my understanding, the LED is always in ON state. Once the button is pressed, the LED turns OFF just for about few seconds and then back to ON state..
Can i have circuit having LED in OFF state initially and once the button switch is ON, the LED should turn ON. Later after the button left, the LED should OFF.
Can this be implemented using single channel or should use HT12E and HT12D ic's?
Can this module be used to make a wireless microphone?
ОтветитьAre This receiver can apply to Wi-Fi or another else
ОтветитьHello. I am testing my 433Mhz RF Tx and Rx module but it is not responding. LED is glowing continuosly even if I push the switch. Can you help me?
ОтветитьLED BLINKS ALL THE TIME, EVEN WHEN TRANSMITER HAS NO POWER
ОтветитьIs it capable to transmit and receive audio signals??????
ОтветитьCan you please give the details on how to make the 2 antennas. Thanks.
ОтветитьKitne metar pe kam karta he
ОтветитьWhere I get the antina
ОтветитьHi, how I can use the same module only for conductivity not to power a led? Thanks in advance!!!
ОтветитьJesus Christ is coming back repented you my brothers and my sisters
ОтветитьHow many meters
ОтветитьCan we use LORA modules in same way, without Arduino ?
ОтветитьSo what determines the signal? Will all transmitters shoot the same signal? Can we change that signal? Talk to me about the signal... :) Can we make one just as simple but more secure? This is very cool. But can you show us the next step UP? LIKE CLEARING SOME OF THE NOISE or adding range or another button. I've been using the arduinos but I'm not too good at coding. I can't seem to receive a signal and have that signal trigger an event. Not even to one pin
Ответитьwhats the gain at the output can it gove rf burns ?
ОтветитьHey could I get name of song? Sounds nice
Ответитьwhat is the max. range of the distance ?
ОтветитьCan I use a normal switch instead of a micro switch
ОтветитьCan you tell me what the current consumption of receiver module when ideal ON but not receiving anything?
ОтветитьI did what you say. But When I powered the reciever module , led starts flashing. Even If I press the transmitter button the flashing state does not change.
ОтветитьWould it work if I put a motor in it instead of the LED light?
ОтветитьKya led ki jagah moter chal Sakti hai
ОтветитьCan I see the circuit diagram of this plss?
Ответить