Комментарии:
hi, i was abe to download and add the layer 2 switch but its giving me
"No bootable device." error
Hello, what can I do if I want the switch to have fast ethernet ports?
ОтветитьFacking worthless and music SUCKS!!!
Ответитьthank you sm
Ответитьdownload image does not work?
Ответитьagain and again, restart my switch. use for this ios
Ответитьthx alot man
Ответитьemeğine sağlık
Ответитьgiving me error "HAXM acceleration support is not installed on this host" . what to do ?
ОтветитьHI i can only add 3 network adaptors. is there any way to add more?
ОтветитьHey, I'm having issues opening the switch. When I chose start, get an error : " HAXM acceleration support is not installed on this host".
How do I get around it?
thanks
Hi, I am having issues. I have installed the L2 & L3 but I continue to get Duplex Mismatch. It is auto negotiated. The switch is not full-duplex and the router is. the media type is rj45. (not sure if this has anything to do with it.) Please advise. Thank You.
Ответитьveeeeery Tanx
Ответитьyou cab only add 3 adapter?
ОтветитьHey How many GIG port we can configure in this L2 Switch ?? I tried adding 10 but the switch was not booting up it got in some kind of loop. Please help!
ОтветитьThank you for sharing
Ответитьhalf duplex ports
Ответитьhaxm acceleration not installed ont host error i got
Ответитьthanks a lot for tutorial and iosv2 file....
if somebody has issue search in google
I had HAXM issue and search it in google and solved my problem...
never give up
Hello, I got an error "haxm acceleration support is not installed on this host" I can't start the switch
Ответитьi got prompted with telnet and vnc , whcih one should i select
ОтветитьGreat video bro
ОтветитьHello There, I followed your video and it installed OK BUT the IOS doesn't load when I telnet in can you assist I am using GNS3 2.1.21
Ответитьthe link doesnt work update your vids you lazy fuckin asshole !
ОтветитьThank you very much
ОтветитьThat image doesn´t work for me :( Buuut thanks :)
ОтветитьIt’s not working. When I console into the switch it stays black and no text comes up.
ОтветитьExcellent help!
ОтветитьIf you need more intrefaces, you have to change the memory. 256MB = 4 intrefaces, 512MB= 8 interfaces ...etc
Ответитьtks bro...
Ответитьthank you , keep on doing what you do best
ОтветитьI tried to added it but keeps rebooting.
ОтветитьVerryy Goood !!! Thk !!! 10 up
ОтветитьThanks a Lot :)
Ответитьexcelente, thks so much
Ответитьthank you very much
ОтветитьIt's not working
ОтветитьHow to setup qemo
Ответитьthanks good video
ОтветитьThank you very much!
ОтветитьAwesome!!
ОтветитьWhen installing on MAC, I'm not able to see the switch on installed appliances. Any advice?
ОтветитьTe lo agradezco mucho.
ОтветитьThanks a lot..
ОтветитьHey bro, Can you help me?
I have install IOU L2 SW in GNS3 2.0.3, I can not ping through IOU sw.
Example:
Simple topology => Router - IOU (L2) SW - Router:
+ I config interface in the same subnet but I can not ping each router another, but I replace the IOU sw by ethernet SW in GNS , each router can ping with another.
+ I have try many version of L2 IOS but it not work and config no ip routing, no shut interface,no shut interface vlan 1 but is no work to.
Tks you!
Thanks for your video, That was a good way, But is very Slow
ОтветитьHello , Thanks for this easy step switch build on GNS3 , I just have a doubt when writing the configuration after the reboot of the switch it goes back to default configuration as if I did nothing any solution please for this ?
Ответить