Комментарии:
I have a ender 3 v2 neo, if i use these settings, will it be okay?
ОтветитьAmazing print quality
ОтветитьTorture toaster came out 10 out of 10!!!!
ОтветитьAre these settings still valid for the new Cura update ?
ОтветитьNice, you saved me so much time...
thanks
I'm wanting to use these settings with cura 5.1 But there's a setting called maximum extrusion area deviation Under mesh mixes?
It's set on 2000 but that can't be right can it?
are these settings good for ender 3 v2 also?
ОтветитьI NEED HELP....very green
ОтветитьOk but for real! I got my ender pro a while back and I have been fighting for my life to get a good print on this thing. The only good print I got was the test print it came with and I have been struggling since. I found your video a few hours ago and just completed my first print of a model I made and it came out flawlessly. Seriously thank you for this video!
Ответитьtoo fast
ОтветитьHello Can You Please Upload A Video On The Perfect G Code To Have For Cura Settings Because For Some Reason It Keeps Saying I Don’t Have The Right Settings To Print My Little Piece
ОтветитьHi I'm printing on a glass bed how do you think my settings should change to adjust?
ОтветитьI dled and wanted to try your profile, but I noticed something in the preview. My model has my small logo on the bottom(first layer) as a hole that's 1 layer thick (0.2mm) that usually just has the 2nd layer bridging over it as an effect, but with your profile the logo is totally gone and my bottom layer is filled solid. I tried looking through but couldn't figure out which setting does this? I tried both 0.16 and 0.2 profiles and both completely remove my logo. Can you tell me so I can turn that one setting off? Thank you!
ОтветитьWith how many people are praising these settings, I'll give it a shot.
One question, and I'm just going blind on it. Will any settings need to be changed if I use a .6 nozzle or should it work just fine?
For your dynamic pla settings wich nozzle size you use and blass or metal or..?
ОтветитьHow do I get my Mac to recognize the printer - do I have to do anything special for it for to recognize it? I’m on Monterey
ОтветитьI'll try them tomorrow and hope they will work thank you in advance
ОтветитьLove the video! May I know which PLA filament do you recommend? I just started printing and I'm using the Creality filament, when I did the retraction test, theres too much much retraction and I'm not sure if its the filament's fault.
ОтветитьThank you!
ОтветитьStill brand new to 3D printing would these settings also work for super quality?
ОтветитьDude your audio is trash.
ОтветитьCan you do tpu
ОтветитьI have been using your settings for Pla and my prints have been amazing! I appreciate you sharing your settings and I thank you for this video!
ОтветитьSo I own the ender 3 pro and used your settings to slice the models I got from thingiverse. But now my printer prints small circles and runs through my filament without going up. What am I doing wrong?
ОтветитьThanks appreciate The vid I new to printing so this helped a lot
ОтветитьI have a 3v2 ender, I just want to try Cura slicer before I used Peusaslicer and Superslicer. Can your profile be used on Cura version 4.11 especially for abs?
Ответитьhi I have to let you know , what a brilliant video just started 3D printing , and could not understand about profiles but you made it so simple , even I could understand and more to the point do them and they worked you are a natural, there is no videos on the internet I can find that explains how to save different profile 's . a very big thank you .
ОтветитьCan I use 0.2 filament with these settings
ОтветитьThank you for working hard to get this info to the internet
ОтветитьCan you do one for petg
ОтветитьYa really good thanks
ОтветитьI’m still getting bad prints
Ответитьcan i use the pla format that you have, with all my builds and it should run efficiently??
Ответитьcan I use these settings for PLA ?
ОтветитьWill this work for ender 3 or it will only work for ender 3 pro
ОтветитьBro, thank you, I will be testing this. My best moves tomorrow, but his mom is staying a bit before they move, I will print out something for him to remember me for. I wanted to get him something high quality so thank you.
ОтветитьWould this work for the Ender 5?
Ответитьthe prints come out so good but it takes forever now.
Ответитьsome of the settings are not showing up on cura
ОтветитьI must've something wrong because mine are certainly not printing right
ОтветитьI tried your settings for the ABS last night on my ender 3 V2 which has been upgraded with a dual Z axis, Dual gear extruder, BL touch and a all metal hotend. I checked my print this morning and it seems to have the seam very noticeable now, roughly 50% more noticeable than before. Is there a different setting I should be trying? I will ad that the print was round and with 100% infill, the part made is to replace my stock reverse lockout that you pull up.
ОтветитьYou just made my life easier :) Awesome settings. (Subscribed)
Ответитьuhhh this is the default settings with like one thing changed
ОтветитьThanks a lot, i have been using this configuration and the performance was insame
ОтветитьIf we do decide to have supports, what should we use for settings?
Ответитьvery valuable information 😍 thank you good job 👍(Googletranslate) 😁
ОтветитьWould these work on a crs10 pro v2
ОтветитьI dunno if it is other settings I changed or your profile, but the .16 profile works like a charm for me! Thanks!
Ответить