Fnirsi LCR P1 Transistor Tester | New LCR Meter Components Tester Review #LCRP1

The best tester would be a scan tester, scan the board and find the fault

Have you learned how to export the test results , if yes please explain how to do so. The add on Banggood says should be easy to do. I have had zero good luck.

Beware, this is not a review, it's a shallow puff from the supplier. The device is nowhere near as effective as the much cheaper M-Tester (I have both).

💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯💯

Why playing music with your video????

For general component identification and testing at a 3600MW, 6 generator power station and it's electronic modules, this device is great for fault finding on 1975-era Siemens, Brown Bovery, Alsthom, Measuretronic, Ultrakust, Semicron, Hartman & Brown, GE, Multilin, ASEA, BBT, ABB, Credfield etc. cards. Yes, it is not the best, but beats the crap out of most other test instruments. This unit should be seen as a helpful tool, instead of a high-accuracy, calibrated highly expensive test rig like the PinPoint Sigma or similar test units.

This tool is absolutely garbage. It looks nice, but that's it. At first you have to compare with the cheap testing tools for not even the half of price from it.

Most important question - Is it any way better, than previous model TC-1, which failed to test IGBTs, because voltage was too small to open the gates ? To be honest it is a biggest concern for me, I am looking for tester able to do this, and I hope, that Fnirsi had made some research this time and improved faulty functions of previous model, plus added some new abilities. I hope, that they cooperated with a team of electronics to make this time a really good product, and that they didn't just paid a designer to put 5$ worth old circuit into a nice, new enclosure. Otherwise this thing is a total waste of money and i am definitely NOT going to buy it, especialy when they threw out oscilloscope from it and when i have seen how shitty is the new Geiger counter made by Fnirsi! Seriously - I liked old stuff, but now i am close of starting to hate this company for they new politics!!

Not a complete review

Good looking product, but the functionality of the whole device is not good. During the tests, I discovered errors in the firmware and although I have asked the company several times to fix the firmware, so far without success. The product does not measure very well and has no setting menu. For example, when measuring diodes, he is unable to correctly mark the cathode and anode. And that's just a small detail. I do not recommend the product, you will be disappointed.

Good tester I think…how will be that price?

It tested the LCR-P1 and it is really bad. It seems similar to the TC1 component tester but it is no way near as good. It cannot recognize Schottky Diodes it thinks they are resistors. It can't recognize Thyristors, dual diodes in to220 packages. And the capacitance and ESR is also inaccurate. And it is much slower than my TC1. I emailed FNIRSI several times but they won't respond. Stay away from it.

新玩具

Could you install a diode or zener diode with a cathode from the right.
Will the polarity of the electronic component on the screen correctly display?
Also with transistors.

Can you measure ESR of Tantalum capacitors?

А что за подставку вы используете? И хотелось бы увидеть внутренности прибора :)

have you tested rds of mosfet does it shows perfect or it has some bugs in software like fnirsi dso tc3.
i had 1 dso tc3 rds on according to datasheet is 2.4 ohms and dso tc3 shows 0.4 ohms to 0.5 ohms this meter also had same problem.

FNIRSI DSO TS3 and TS2 do not measure ESR correctly or do not know how to measure it at all! Fnirsi LCR P1 - Does it know how to measure ESR and does it measure correctly?

I don't think so. This is not how you test a TESTER. You have to test against leaky and faulty components. No one needs a device that states the obvious. Unless you are blind and can not find this information yourself. I've been wanting a device that can actually run diagnostics on a component using simulated workload and use its datasheet to compare parameters to give me an actual result. This thing is a toy, no serious technician would use professionally. That blue led diode is 3 volts, 20mA that reading was wrong.

nice

A jak sobie ta "maszyna" radzi z odczytem tranzystorów IGBT? Bo wiem że w pierwszych urządzeniach tego typu jest problem i nie potrafią ich poprawnie odczytać.

Hi, someone knows if these meters can test IGBT's transistors?
Thanks in Advance.

What Is ir-decoding?

Проплаченая китайцами реклама очередной поделки. Ни одного сравнения показаний с прибором которому можно доверять. Тупо демонстрация возможностей для тупых хомяков. Автору должно быть стыдно за подобное!

IGBT?

Is it based on m5stack module?

no ESR reading?

Pity for the horrible music and p l e a s e NO more unboxing time wasting!

I really enjoy watching all your videos, is there somewhere I can buy the circuit boards and components all in a kit ready to solder together

What method are you using to verify that the measurements are accurate?