Комментарии:
I’m just curious why you say you’re going to use tweezers to remove the glue when clearly you were using a razor knife 😂
Ответитьwhat's the p/n for the replacement LED's?
Ответитьyou don`t need this but for free i would take it i use a hot air gun
ОтветитьUsed this to repair several strips without having to buy new ones. Removed individual LEDs from an old discarded strip and reinstalled on the one going into the TV.
A word of caution. If working on the LED next to the power input jack of the strip, use Kapton tape to hold the power jack in place while working the LED. I had to go hunting for mine after if fell off along with the removed LED!
I know this question is maybe stupid! Regardless I need someone's help.
(Q- can I use a flashlight led to replace the bad led's on my tv??)
How did you know which LED to replace it with?
ОтветитьOn ne voit rien
ОтветитьIt`s so slow method :(
ОтветитьHow to repair the power supply for ledbackligth samsung 40"
ОтветитьWhat's the name of the machine
ОтветитьGreat vid, thank you, the problem I have is the larger soldering joint on the strip is Possitive, but the larger area contact point on the LED is Negative !
ОтветитьWhat temp does the plate go to ?
ОтветитьI just tried and it only works when i reverse the pos and neg?
ОтветитьDo you also selling parts only, let's say LED or LED strips?
ОтветитьI wouldn't go poking at the LED's face with tweezers, especially when they are hot. They can be damaged easily.
ОтветитьNew friend, Full support Godbless.
Ответить👏👏👏
Ответитьafter replacing led i get these round rings "circles"
ОтветитьSir... Led strip light mein ek mistake ki wajah se.. 240 volts se direct connect go gaya... Ab 12 volts driver se nhi jal rha h... Kya koi solution h... Sir.... Is baarein mein jarur batayein... Dhanyawad!
Ответитьis there a positive and negative side to the LED or is that not important because it's a diode? Also, the 2 solder pads...do you have to worry about solder bridging the pads?
Ответитьare the leds universal???
ОтветитьShouldn’t led’s last forever??? Why would they go out on a tv after leas than 2 years ?
ОтветитьDoing this for the first time requires a skill level to be built up. Then you may find that the surface mount pad on led is different to to that on the strip. I opened the pad gap on the strip pads to minimise short. I used hot air gun but that will blow the Led off the strip. Used a made up tool that allowed a screw to bare down on the Led whilst being soldered. Test as you go. I used about 40 DC across 14 LEDs. Check for flickering LEDs. Replace as they may be on the way out. Replace any LEDs that are dim. I ordered cold white half watt 3.4 volts. The light has a slight yellow look so when I finished the repair may need to set tint levels to compensate. LEDs back in frame so next job is to re fix the diffuser lenzs then the white back sheet. Two days work so far but speed is increasing. The shop Jimmy hot plate seems cleaner but more for the professional. My wife was not too keen on me using her iron. Thanks shop Jimmy for all the advice.
ОтветитьMy master Philips 32BLD4012N / 62 has 2 LED bars on the TV, there are 6 LEDs on the bar. There is no sound, there was no image, I changed the LEDs, they did not light. There is 13 v electricity to the sockets but it does not light up. I wonder why
Ответитьnext time let the old glue soften with the heat it will come off very easy
ОтветитьI need this. Where can I get? Call me 9381149244
Ответитьha ha ha ,never seen such shit advice how to replace single led .First do not remove old glue as you loose proper lens position, second do not warm strip as white paint become yellow and plastic ring may melt as well , you should use solder iron tip and sharp knife to remove old led. Than new led should be soldered using soldering paste. Super glue is not suitable as it leaves white marks on lenses. Use UV glue.
ОтветитьSir wer u buy a rework station heating, for led beads
ОтветитьSamsung 32" Samrt LED TV Backlight Replace Part Number please
ОтветитьThat station thingy is 40 bucks on amazon 😂
I use ac heating element. only cost me like 5dollars lol
So buying a whole strip is easier
ОтветитьIf your TV has few burnt LEDs don't do the same mistake as I did and only replace those faulty LEDs. Joy of working TV is quite short lived and dark spots soon start to reappear on the screen as rest of the old LEDs die one by one. Either replace them all or bin the TV.
ОтветитьWhat number of led is that sir?
ОтветитьYou would be better off with a hot air gun because this thing is pure junk it will cook you're strip before the light comes loose.
ОтветитьWhat kind of super glu you are using?
ОтветитьWhat is the price of led strip rework
ОтветитьAny Nimrod would test the LED before putting all that crap all back together, which you did not do.
ОтветитьI tried a lot but failed
Ответитьthe video is very good. please watch to my channel
ОтветитьIs to expensive no good I make one station
ОтветитьJust got mine, and WoW makes the job sooo easy and quick. Also got the LED tester, great combo.
ОтветитьWhat glue did you use? Please answer glue's name.
Ответитьwhat is the ( single led size and type ) am getting in the busniess and want to order from aliexpress .. what are the most common sizes used in led lcd oled tvs ?
ОтветитьI would test the replaced LED first before gluing the lens diffuser.
ОтветитьSir good evening how to unlock key lock?
ОтветитьYour Using glass joing Paste Name.... Answer me
ОтветитьI recommend two soldering irons used in a tweezer action. Needle point tips and it's too easy. One question, how do you check which voltage led to use? 3 ,6, ?? I got a Hisense. Many leds gone. Will order cheaply from AliExpress but not sure if 3 or 6 v. I used 8 v across two good leds and they shine quite brightly. I'm guessing 3v. Edit; there are numbers on the strips that led me to the correct led from aliexpress. 50 beads for 2 bucks.
ОтветитьHow hot is that plate?
Ответить