Комментарии:
Allow me to introduce a new unit of measurement for sound volume,
which I call vovol* (abbreviated: volume voltage).
THIS IS HOW IT WORKS: You use two pre-stages, one with positive volume values, and the other negative.
For example, so has the pre-step with positive values
a measurement from +0 decibels up to +20, while the one with negative values, has from -0 decibels down to -20 decibels.
The highest voltage occurs when the value is
+20 and -20 decibels (or: 20 vovol),
while there is low voltage, when the value is on
+0 and -0 decibels (or: 0 vovol).
You can possibly also combine two different values with each other, by adjusting the value to +10 -20 vovol, which gives a crisper effect. Have experimented with this myself at work and at home.
The adjustment can of course be set to taste, but the purpose of vovol for me is to equalize the sound volume, so that you better hear weak sounds and at the same time avoid high deafening sound levels (loudness war's).
Thank you for reading this!
Take care of your hearing...
:-)
Awesome video anyway!
Ugh, here I was thinking I could just hook a pot inline from power to the speaker 😫
Ответитьdon't forget to use the ground pin ;)
ОтветитьFake my not working really I do same wireing
Ответитьno labels, diagram or speaking irritates me its almost like you just wana show people you can do this rather than showing people how whats the point???
Ответитьhahah, it is in reverse way! lol
ОтветитьDiggin the guítar. Yeeeeah. Great vid. Ty!
ОтветитьKreatif jika potensio 4 kaki bagaimana ?
ОтветитьCapo me salvaste la vida algo que me costaba resolverlo vos lo hiciste en un segundo capo máster idolo
Ответитьyou can connect a jack connector and not the and not the jeck itself
ОтветитьPor favor lista de materiais do amplificador
Ответить👌👌👌👌👌👌👌👌 I have been searching for it everywhere
Ответитьhello friend can you help me with a connection
ОтветитьI wonder why you for 5 minutes flipping this pot are slow brainer,
ОтветитьYou didn't show "how to use a potentiometer" but "how YOU used a potentiometer".
ОтветитьHow to give gtound connection
ОтветитьCan u please name the components use capacitor uf and v?
Transistor code.?
Resistor ?
And is it necessary to use that twisted copper wire ?
And what is the input current 5v ? Ok for it please reply
Your sound is increasing by rotating anti clock wise and decreasing by clock wise..
ОтветитьInteresting how nobody is pointing out that the pot is wired incorrectly. You didn't use the ground pin.
ОтветитьIs that nokia c5? I used it for 7 years.thats my fav
ОтветитьWrong wiring... for input
ОтветитьPoor demo..
ОтветитьWill a 25k potentiometer work fine?
Ответитьwhich integration do you use here ?
ОтветитьMy name Varun
ОтветитьHi, I'm using a 6-pin(3x2 pc16d) stereo potentiometer in my project. I couldn't find the component library for schematic and pcb drawing in Altium.I'd be glad if you help.
Ответитьwhere is the circuit bro? how is it making?
ОтветитьSick sound system bro, really slapping there. Thanks for the video, just what i needed.
ОтветитьBhaiyo yha par jo video hai yh bekar hai pehle se nahi batate ki kya karna chahiye
ОтветитьSo much useful information given.
ОтветитьHow to make this
ОтветитьYou can use one transistor
ОтветитьIn my case after adding potentiometer.. Volume get bit decreased on full (b50k)... Please help... By the way thanks for connection setting as I was confused.. I am not a electronic guy...
ОтветитьYou ARE indian.
ОтветитьPlease upload the video
ОтветитьHey bro how to connect bass and trebel in stereo amplifer single humming
ОтветитьIs it works
ОтветитьHow to make diagram
ОтветитьHello
ভাইয়া আপনি কী এই video এর ডায়া গ্রাম দিতে পারবেন প্লিজ প্রারস এর নাম্বার বললে দেবেন।
hello CD! I tried using a mono potentiometer between speaker and amp, got sound, but the potmeter does not react linear... is it to do with the set-up (hot signal) or the potentiometer? thanks !!
ОтветитьLOL - this may have been covered in the comments, but I couldn't resist... in most parts of the world (Universe I'll bet) you turn the shaft to the "left" (counterclockwise) to lower the volume and to the "right" to raise the volume (clockwise). If you are going to use that, grounded or not the outside wires need to go to the other far side. Click "Read More"
==================================================================
Ground Audio--->|<-Left pin of pot looking from front=Minimum Volume (no audio)
|
Counter Clockwise = Wiper to ground
| <-------------- Center Wiper pin --> feeds input to following Amp
|
Clockwise = Wiper to directly to audio
Left Audio Out-->|<-Right pin of pot looking from front=Max Vol
==================================================================
Duplicate for the right channel with common ground if allowed. It's not
allowed in most class D amp outputs. NO COMMON GROUND IF CLASS D.
Capacitor
ОтветитьTransistor kaun hai
ОтветитьUnfair advantage, you know wtf you are doing.
Ответитьسلام دوستان عزیز م
ОтветитьThank you Nice idea video channel
Ответитьcan you tell me the purpose of adding the capacitor is to block the DC current to pass through the amplifier?
ОтветитьSong link please 😄
ОтветитьThis is risky
ОтветитьHey bro please tell me that headphone jack wire left and right colour code
Ответить