Комментарии:
Smart idea to make a bearing puller from scrap metal
ОтветитьBisa ngga buat pompa air kecil
ОтветитьKalau buka impeler pompa air bisa kayak gitu bang
ОтветитьGoogjob
ОтветитьVery compact and simple Design and cost effective also
ОтветитьTracker untuk ambil bearing jempol ide as
ОтветитьPlease back help
ОтветитьGood job
ОтветитьVery nice bro
ОтветитьHi bro
ОтветитьBest video on the subject so far.
ОтветитьC'est bon.
ОтветитьÇok güzel eliniz sağlık Allah razı olsun hayırlı aksamlar
ОтветитьGood idea, I'm going to make one for myself, it turned out great!!
ОтветитьKalo untuk bearing gede ukuran berapa pak kalau untuk bikin
ОтветитьSuper 💓
ОтветитьOk
ОтветитьOk
ОтветитьGreat idea
ОтветитьGreat simple device! The improved design (the blue one) is better though 😉 That's because the material tends to stretch 👍🏻
ОтветитьThis the best idea. I have never seen like this.
Ответитьرائع
ОтветитьCongratulations !!! Easy to build and works very well !!!
Ответитьbem bolado e dimples
ОтветитьSuper tool
ОтветитьEquipment for bearing,... very helpful
ОтветитьTop!
Ответить10
Ответитьye bolt rad hai jo kitna mm hai
ОтветитьThe most simple tools to make.
ОтветитьGreat idea, retarded music.
ОтветитьWowww excellent 👌👌👌👏👏👏👍👍👍
ОтветитьDimensions plis and good video
ОтветитьGreat job. Bolt size. ???
ОтветитьAq senang nonton kreatip
ОтветитьOk
ОтветитьBagus aq seneng dgn kreatip anda
ОтветитьVery nice idea! : ) What u think about that nut on the inside?
Ответитьawesome tool...I like you to make a ball joint separator tool ( not a press ) to separate ball joint from nukle...I expend $ 500.00 on 3 different ones...and believe me you will need a thicker steel and a thicker stud...that will be awesome to built..thanks for sharing
ОтветитьI think this is for one dimention only.
ОтветитьBom dia você pode mandar as medidas
Ответить👏👏Meus parabéns 👏👏
ОтветитьGreat idea simple and effective. How to repair vacuum cleaner so I'm making one of those today.
ОтветитьBom show.
ОтветитьElhamdulilah
ОтветитьWith a little creativity this could be adapted to become a track - rod end cracker ( splitter) for the always incredibly tightly bedded - in tapers on the locating pins , but enable a way to secure it to the job with a short light chain , as I,ve had official special tool versions just explode off with deadly force & terrific speed . I welcome feedback from the blacksmiths out there who know how to make the metal used in making this , incredibly tough after machining , so it does not open up under load use . Constructive comments on here please guys !
ОтветитьЗаибись приспособа !
ОтветитьI like the abrasive disc of your grinder. Hope you can share the specs. Thanks
ОтветитьVery nice
ОтветитьOœ
Ответить