Комментарии:
What brand are those hinges?
ОтветитьOkay! Your video gave me the confidence to go for it!!!! Thanks Anthony! Curious about if I should drill for the pull handles while the cabs are laying flat OR wait until I install in case hinge adjustments are made?
ОтветитьA very informative video on how to install concealed hinges and will come in handy as I have cupboard doors to install next week.
ОтветитьGreat except didn’t show how to line up the hinge at the cabinet
ОтветитьVery good instruction. Gives us the confidence to do our own doors. Thank you!
ОтветитьNow check to see if your hinge is square. Unfortunately its a well reported paradox that the Kreg jig is out of alignment for the two screws so always use your square and a self centering drill bit to put those pilot holes in. The 35mm hole positioning works very well indeed, it's just those screws.
ОтветитьYou are a very good teacher I wish you had a school to teach cabinet making classes
ОтветитьTrust me if you had a drill press kreg is thrown in the garbage trust me ive built hundreds of doors n cabinets this is a diy weekend
ОтветитьCool channel dude. Subscribed!
ОтветитьAnthony, It appeared you did not use the screws that came with the hinges. Can you explanation? I am also installing these hinges and am considering longer screws due to size and weight of my 48" high doors.
ОтветитьExcellent step by step instructions great. I went amd got a kreg wow what a difference. Spend the 49 for it. The kreg vivce grips are really pricey. 59 bucks for 1 u need 2 but worth it. I'm just a diy guy
ОтветитьThank you. I needed a refresher and this was perfect!
Ответитьwhat is the number of the hinges to buy the same
ОтветитьJust bought the Kregg jig for the same hinges. Thanks for the intro on using it....Kregg makes great tools.
ОтветитьOk how do you match up the other hinge on the inside?
ОтветитьThere are no manufacturer specs for my hinges and it was the only ones i could get my hands on. Now what? Guess i will just have to start on 3 and test the jig on scrap wood until i find something that works
ОтветитьI believe I can actually do this! Thank you!!
ОтветитьI liked your step by step instructions in the installation of these hinges. A little constructive criticisms, your should have turned the clamps over, when clamping the jig in place, to keep from denting the face on the front of the door. Or use a scrap of plywood to minimize the impact. All-in-all a good video.
Ответитьgreat video , can you one drilling and installing the door on the cabinet , is there a jig for the other side??
ОтветитьNice! Also, looking for guidance on how install the hinges on the cabinet getting it nice and level in addition to having it centered top to bottom of cabinet opening.....
ОтветитьGreat work Anthony. Simple, concise & sharp results on the matter at hand💯
ОтветитьThanks for the instructions! However, how do you precisely measure the heights of the other halves of the hidges that were already scerewed in the cabinet (at the end of the video, when you connect the hidges and put the door on)? It could be useful to show that, for us beginners :) thanks in advance!
ОтветитьHi, Do you use anything to put the hinge on the cabinet frame? I'm redoing my fronts and really nervous about messing up!
ОтветитьToo much talking, like u are infront of movie camera, talk clearly it seems u have soup in ur mouth
ОтветитьBut it is close to the edge!
ОтветитьAny trick to installing them to the cabinet now the hinges are on the door? How do you hold the door and drill pilot holes in the cabinet at the same time without it slipping on you?
ОтветитьThank you.
Ответитьgreat job 👍 thanks for info
ОтветитьGreat job!
ОтветитьI am replacing my old hinges with soft close. I’ve patched holes from old hinges. Do I need to change where I install new hinges? I’ve read about wood fillers, epoxy and putty, they all say you can drill them but they are not strong enough to hold cabinet doors. My old hinges were placed 3” from top and bottom, should I change measurement when installing new hinges so I’m not drilling into wood filler or epoxy?
ОтветитьThis is a good instructional video. Thanks for making it. Direct, to the point, not a lot of fluff.
Ответитьi am having issues with the PVC doors that was just installed - soft close lap ones, what is the solution to ensure that the hinges hold onto the board. the screws come out
ОтветитьCan anybody tell me what the screws are for that go on the cabinet side of the hinge not the Dior side and not the mounting screw but the two other ones that come factory
ОтветитьWell done, so helpful, I installed my doors following the instructions of your video. I like the way you tell people to look at the manufacturers specs, so I did that! Doors are on my kitchen cabinet, Thanks!!
ОтветитьVery good I like it
ОтветитьExcellent video thank you.
ОтветитьBro you don't know how much you saved me . I appreciated this video.
ОтветитьSo does a Kreg system does come in Metric or is it a combination of imperial as well?
ОтветитьAye, this guy is considerate!!! appreciate ya!!
ОтветитьThank you for this video. At my wife's request (of course ;-)) I am replacing flush mount (full inset partial wrap?) hinges with soft closing, concealed, mortise-type hinges (as you install in this video). Our cabinet doors have a routed hidden curve (grab edge) all around the edge. This means when looking at the cabinet straight on there's a 1/2" overlay but because of this routed grab edge the actual overlay is about 1/8". When measuring the overlay for a mortised soft-close hinge I suspect I should use the outside edge of the door; in other words the 1/2" since that is truly how far the door edge extends past the frame edge. Correct?
ОтветитьWhat size drill bit did you use to drill holes on both sides of the circle?
ОтветитьI have a vanity mirror with pocket hindges and its rubbing against the bottom shelf. How do I adjust this?
ОтветитьExcellent video. I was all set to buy a drill press just to replace my cabinet hinges. You saved me a ton of money and garage space for a tool I didn’t really need. Thank you
ОтветитьThank you so much for this very in depth demonstration it was very helpful. Appreciatecha!
Ответить"they don't even know I exist"
ОтветитьHow did you lay out the plates in the carcus?
ОтветитьThanks Anthony for clear straight to the point video, appreciate it!
ОтветитьThank you..👍
ОтветитьHi my door does not sit flush on the frame, there is about 4 mm gap and we have maxed out the adjustment
Ответить