Dolby Atmos Setup | Denon AVR Setup | Amp Assignments

Hi. Great video. I just bought the Denon AVRX4700H. In the manual I don't see a connection configuration that will represent the speakers I have to connect to it. There will 5 floor speakers (FR, FL, C, SR, SL, plus 2 Dolby enabled FHR, FHL (assume connect to Height 1) but I also want to Bi-Amp the Front Klipsch 8060's, and would likely use the Height 2 connections for that. They have 7.1 channel:Bi-Amp Connection of Front Speakers in the manual, but in that configuration they show an SBR and SBL which I do not have. When I hook up all the speaker wires and run Audyssey, will it figure out the correct configuration to ASSIGN? Thank you in advance for any replies.

I have the same setup as yours, but I have rear top also. My atmos setup only shows two channel for atmos. I have a denon avr x6700h.

Awesome video, thanks for sharing

EXCELLENT video presentation. This man covers it All. I have the 7.2 Denon
and yes, there is a lot to work with and I'm not too familiar with receivers today. This is just what I needed,
Thanks for sharing your time and knowledge.

If you use bi-amp connections from the four posts speakers, where do you connect the top speaker posts and low speaker posts to the A V receiver.About the crossover part,some say you should set it about 20 hertz more than the lowest hertz indicated on the speakers specs.

Top front 150 hz ? Why? Reason
Isn’t they sound too sharp?

I just installed a pair of Martin Logan Vanquish ceiling speakers for atmos speakers. I use a Denon AVR-S930H, I used the Audessy eq and for some reason I can’t get a whole lot of sound out of the ceiling speakers. Any tips??

Great video!! I have a couple of questions. Here is my setup:

Denon 4700
Klipsch R-625FA Dolby Atmos Floor stand speakers
Klipsch RP- 504C II center channel
Klipsch R-41M Bookshelf speakers
Klipsch R-12SW subwoofer


1-What are your suggestions for the crossover settings?

2- What are your suggestions for the db level for all the speakers? This is where I am confused.

Excellent video! Thanks! I'll try to get my setup working and I'll probably be back with a question or two. Again this video is very clear and I didn't have to pause once. :) It's not a rush job,

Hi I have a denon 2800h running a 5.1.2 I have mounted 2 Dolby Atmos speakers behind my seating area on the wall just near the ceiling as I couldn't fit any ceiling speakers due to not having a flat ceiling my question is in the denon settings there is nothing were I can tell it about the rear wall mounted Dolby Atmos speakers placement

Very helpful!

Can you do a video for Denon AVC-1500 5.1

Hi Please assist Subwoofer Bass crossover… And Calibration settings for DTS X or Atmos

Do you have any idea how to get MacOS's "Audio MIDI Setup" to recognize all 13 channels and send audio to them?? It seems stuck at 7.1 or 5.1.2 MAXIMUM. My Odroid sends Atmos to the Denon AVR Just Fine By Default.

I am using DENON X1200W ...need some guidance....When i set to Dolby digital ...no sound is coming out of Back surround channel(L&R)
., only settings @ Dolby surr and MULT stereo ch can i hear the sounds from Back Surround channel L&R

whats the purpose of crossover setting in Hz.....is it for speaker assignment.... higher range(e.g F35 jet flying) to lower range sounds(speech / thunder roaring)

how do you come to this page? on TV or handphone apps

Hi sir I have a Denon X1200W…
When I set to Dolby digital, there is no sound at channel SURROUND BACK L &R.

Mode Dolby surround and multi channel was fine.

Why is it so ?

hi im currently running a 5.1.4 set up with a dennon avr 4500 amp and I've ran the audssey app but am so confused about all the settings and how to adjust them ? its a minefield of info and I wondered if I send my calibration details to someone the would be kind enough to have a look and help me please

Hi, I have a Denon Pro dn 500 av preamp, impossible to get acces to HDMI imputs no sound, I connect a Notebook I define Denon but no sound appear. Can you help me Dad?

Good video. Expect LFE at 120hz is only for some super tiny speakers setup. At that point save your AVR money and buy better speakers.

I like 80hz for surround. 63hz for stereo.or 50hz if I had full range larger towers.

"But.. whatever." 🤣 It's been 5 years.. are you still married?

Great Video😎

hy there ,techno dad I have a problem with my denos , I make the audissey setup and almost all the speakers ,the receiver turned off only left the front, what I making wrong...

Hello Sir, currently I have Denon AVRX 6500 H. how can I preamp the front two speakers in 11.1 step up? I see in this video you are showing 9.1 step up Bi-amp, but below speaker for Bi-amp is hight channel; how can I change this to front speaker only?

Hi great video question please if you don’t mind. I just finished setting up my home theater and I’m first running a Sony A90J 65 inch OLED, my question is I’m using a Denon 3700h receiver with two Klipsch RP-800F’S front speakers and two R-41sa’s as the height speakers which are mounted to the wall on each side of the tv cause I didn’t like when you place them on top of the floor speakers and aim it at the ceiling to get the overhead affect. I also have two Klipsch RP-600m bookshelf speakers on stands as the rear and I’m using the tv as the center channel until I get dedicated center speaker, there is a 10 inch woofer as well. Now the entire setup uses hard wired connections and I just bought two Denon 150 home wireless speakers and I would like to use them as rear height speakers to make it a 7.1 but so far I’m not seeing a way in the Denon setup to add two wireless speakers it only gives options for connecting more wired speakers. So is it possible to do this? Thank you so much

i purchased 4 front speakers. i’m having a problem with putting the 2 independent if that makes sense

Why should I set my large speakers to small?

Does the Denon 3700h have the ability to run dual front L and R speakers and 6 atmos channels in the speaker configuration?
The way my movie room is set up doesn’t allow me to have rear surrounds or rear side surrounds.
I know it’s capable of processing 11 channels, just didn’t know if you were only limited to placing your speakers only in areas limited by the receivers speaker configuration set up menu.
Thanks

I've a Denon X2400H. I was curious if I connect another AVR via Zone 2 can I increase the amount of speakers connecting both receivers via zone 2? So I can have 7.1.4 for example?

I have a question. My current setup is front dolby 5.1.2 However I don't understand the proper setup for front dolby R and front dolby L.

Great information. Thank you

Model denon ?

Sir can I connect my Panasonic Bi Amp speakers with Denon 7.2 dolby atmos AVR?

How come Xbox series x games don’t display atmos on my denon when playing games and the denon can’t decide them for atmos? Is there a setting on my denon to decode the signal as atmos?

I have dolby atmos speakers that are 2 spare tannoy has xp satellite speakers pointing down in the corners of my room.

But when netflix is playing a dolby atmos series it's not showing dolby atmos on the 2700h avr

Is there any difference in the Atmos effect for top rear and top front. Since I don’t have space on the back side. What’s distance I have to keep for top front configuration?

Hi!! I'm happy with this channel of yours👍 i have a question for you...it's possible to virtualize the front and rear sound with the Denon avc x 4700h if you don t have an atmos configuration available? Thanks!👍

Where did you get the HDMI cables and wires and types for this model? I like the clean set up.

What happens if you only have one front speaker

I cant understand how i can set my X3700H front left and right speakers to work with external amp. I plugged preouts to Hegel and front speakers connected to also Hegel left and right. I can play directly from hegel but i cant use denon 5.12 setup with my fronts. What amp option i have to choose to make it work then? I dont see option to use left and right as preout only full preout for all speakers??

I have Denon 7.1 S740H Dolby Atmos Receiver but it doesn't have "height" set ups in the back. My only option is "surround back, left and right" and they are "assignable" so I guess i can assign them to my "front dolbys" for Atmos? Thanks very much dude, Liked and subscribed!

Does assigning new speaker disable audessey ??

Good job on this video!

Nice channel. Any help would be great. I have 5.1.2 as well. BUT. I have 4 ceiling speakers ( middle are atmos) and the rear ceilings are my back surround. I can’t find anywhere in the denon setup that lets me set it up where my back two act as my rear and the middle is my atmos. .

What should my source level be set at ? Nice video

Thanks for the video. So I have the svs prime elevations above my front towers what crossover would you suggest I'm @90hz now. It just seems like I'm not getting enough atmos. Ran calibration as well with Denon x4500h. Thanks

Can you set it up for 7.1.4 and set the 4 atmos to middle and front? I don't really have room for rear atmos sense my seating position is only a foot off the rear wall.

How to I "pre" my center channel