Make a Soldering Iron With a LIGHTER & Do Repairs ANYWHERE!

I love you. The negative terminal on my eskate remote popped off and now you saved me 60$ lol😂😮❤

Anybody else come here to kind of waste your day figuring out how to fix a charger or something simple then start thinking you wanna learn how to actually do it legit lol

Y'all already know I'm not gonna use this for emergencys

its working just for 2 seconds and it's gone

Thank you!!! This helped a lot.

thank you for this video i don't own a soldering iron but this should do

I like the way u think

Thank you very much. I was thinking "this video deserves a subscribe". But guess what, I'm already subscribed!

Impressive and really creative idea!
🤘😎👍

Bro until the heat hits the plastic and burns into the gas then we explode

Couldn’t you just wrap the copper wire strands around a tiny balled up, or chunk of solder, then heat it? Like twist some of the wire strands with the opposite wire, and at the same time, wrap them around the chunk of solder, then light it… I wonder if there’s a way to make a bow&drill type of thing that uses friction to heat up the solder? 🤔

Such a good life skill thanks

I use a small drill peace not work I use 2 different wire and not work I even heat it with a torch flame thrower it still not melt the sold on my guitar cir board dont work now I'll have to go buy a soldering iron for 3 spots and never use it again

These guys do this for a joke. I hear up my wire untill red and not even touch the solder at all

Hi, quick question, I know this is an old video but would try this with a paper clip?

Thank you so much!!!

Great idea.
I made a version 2.0 for this using old vape.
Any type of vape with atomizer that requires coil. RDA to be exact.
Preheating the coil and using it as the substitute for the metal rod you used.

Thank you for saving my life Macgyver.

i love u bro

Nice video, thanks for sharing it :)

Quick question whats that thing you use with the saudering DIY to sauder

Comments were 69 so i made it 70

Can I use copper??

Thanks
This helped a lot

You saved my life.Thanl you so so much

I want to repair a speaker this will help

Putting a popsicle stick between the metal and lighter would be safe to use

need to solder some wires in my ps5 controller, should i try it this way?

Steel wire rool cost

Can you use a paper clip?

I know this is dumb but I want to RGH a Xbox 360 but I don't have soldering tools imma attempt it with this trick

Is the stick in your left hand is iron or metal?

This helped so much because I’m taking a rc boat motor and putting into a lego car I built and now I can solder it

Where do I get this metal rod you are bending

Where's this bush y'all keep talking about and what's there to solder in it

Finally, no i can fix my headphone

What are you melting? What do you call that

awesome bro thank you

Does copper work ?

Thanks for this video, I used it to strip down my C-1 (the non-USB version) and it is pretty much the same.

This is dope. And I love how u said “in the bush” hahaha

what kind of metal rod is that? i use a paper clip and its not working.

Can I use a thick paper clip

A little tip: For a strong proper connection you don’t want to add solder to the wire until the wire is hot. When the wire is hot it melts into the wire and bonds to it. If you just drip hot solder onto a cold wire it’s not going to be a good solid connection, witch is basically the whole point in soldering something. You should not have to melt the solder with the tip of the soldering iron or whatever your using, it should melt into the wire once touched to the wire being soldered. Happy soldering folks!

until it blows up in ur hand...

Thanks Man, My my keybaord's wire was disconnected to the circuit so I had to solder it
But I didn't have a solder, Then I watched this and it worked! Thanks Man!

I little careful is a massive understatement.

Which is that wire which u melted reply plz.....

soldering in the bushes. two bushes ago there was a couple having sex

How long did you heat it up for?