Комментарии:
Can i use this circuit as my home 1.5 Hp water pump?
and will it work properly?
Sir I want that circuit board pls
ОтветитьOnly for demonstration it is not for actual work all are fake.
ОтветитьHow do you reverse it so it takes water out the tank till its empty then refill and empty again.
ОтветитьHi is this project possible for arduino uno?
ОтветитьSir can u give a PPT about it for representation 😊🙏🙏🙏 please sir. We choose this product but we can't make a seminar on it so please help us. govt.pulytechni, Nayagarh ❤❤🙏
ОтветитьWhere I get dagram
ОтветитьSuper demo.
ОтветитьBhai ye circuit buy kar skte hai kya
ОтветитьThat pcb is a thing of beauty
Ответитьcan i use 5v input instead of 12v?
ОтветитьHi, thanks for sharing, justa doubt; this project works with 110-120v too?
ОтветитьDoes this work because water conduct electricity or what?
And will this work on other liquids?
Is there a simplified circuit diagram because I don't want to collect it on a board
ОтветитьPump supply ac/dc????
ОтветитьIs the supply for pump 220v?
ОтветитьConnection complete vedio dalo ji
ОтветитьBro it was not working😢😢😢😢😢😢😢😢😢😢😢🙏🙏🙏🙏🙏🤯😖😵💔
ОтветитьHow much volt supply have you given pumb is it DC volt or ac volt I am asking about 12 volt DC I am asking about another supply for pump
ОтветитьBoard. Ekada dorukutundhi
ОтветитьExcellent
ОтветитьSupply for the pump is used in AC or DC?
Can it possible by 9v battery and 5v relay?
Is the same reply 250VAC 7A, will work on my 880 WATT [220V 4A]
ОтветитьExcellent project!! thanks a lot...
ОтветитьGreat video!
Ответитьtry a syphon to empty it quicker
ОтветитьGood
ОтветитьCan u run a small turbine on water fall from pipe and use that turbine to take water out of bucket.. in that way u will make an indefinite loop
ОтветитьSir please all materials list kor do
Ответитьsir what is this project make in 5 volts
ОтветитьIs there any chance of electrical shock in the sensor terminal?? Cause after making this circuit if i attach the phase line on relay it shock in the water, but if i attch the phase line on the pump than it dont shock. What is the problem and what is the solution
Ответить5+
ОтветитьAc dc power dono dena hai
ОтветитьPlease if i want to add a buzzer where should i put it in your circuit and also I’m hoping it sounds for some seconds
ОтветитьUse stainless steel rods for the sensing probes to prevent oxidation/rust.
ОтветитьWhere is your pump connection. When you demonstrate, then show all connection. It is running by a timer circuit.
ОтветитьThe tap is going off position before reaching stop option. It has a doubt.
ОтветитьGreat
ОтветитьBro I loved it❤ but i have relay module and i want to make with it only please comment how to make it with relay module. I will understand. Comment only no need of making video please bro.
ОтветитьCan we use house pump instead of this
ОтветитьWhere can we buy that electrical board? I'd like to make one like that.
ОтветитьPlease I want to used 220v water pump machine, which relay should I use in the circuit board
Ответитьexplain the probe wires
ОтветитьVay apki video dahky mani banayatha sab thike ha lakin (comon.and On.)tach hotahi band ho jata ha
ОтветитьI bought bc548 instead of 547 and dont have enough time to change it. Can you suggest any alternatives to make it work?
ОтветитьFrom where should we get the pcb design
ОтветитьDear Sr.What software do you use for skill size mm × mm on A4 or Docx.
ОтветитьSir i make but not cutoff dc plz help
Ответить