SETTING A WORK OFFSET ON A CNC MILL

Omg this is so helpful to a haas baby

Very good 😊

Dead simple, super useful.
Thank you.

Thanks !!!

The videos and the study you convey are useful in a good and correct way, I thank you very much for your patience 🙏🏿

How to change the language Mori Seiki accumill 4000(MSG 805)

What brand of electronic edge finder are you using?

I have been a machinist for 15+ years, I have worked on fadal, haas, and fanuc controls.
I like your video... but for me there are alot of steps you have that could be done in fewer steps.

I rarely ever zero the relative table. In fanuc controls I would simply touch the tool off on selected axis go into my offet enter the radius valve and hit measure. From there manual enter my shift for excess and press input. Haas controls are vary similar in nature, fadal has a utility feature that shifts everything for you.

It saves hand jogging the machine up and over to position, inputting into the relative origin, re jogging back to center, re jogging to accommodate for stock material.

I typically use a rotating offset indicator because with your electrical contact indicator, how would you indicate on plastics??

But yes your way is a vary practical explanation for a beginner:)

Hi Tom

Once again thanks for the great videos .

If it will be at all possible could you please up load a video setting up a 4th Axis.
xyz=0
and an explanation of what to watch out for when running a 4th axis

thanks

THANK FOME THAILAND

I've been typing X0 input and isn't working on my old fanuc O-M control, have to see if it has a measure option on the soft input keys tomorrow. Thanks for your help.

thank you so much sir!

Always remember to repent of your sins (sin is transgression of YAHUAH’S LAW: Genesis, Exodus, Leviticus, Numbers, & Deuteronomy) And Have Belief On YAHUSHA HAMASHYACH. HE Died and Rose three days later so that you can be forgiven of your sins!

HE Loves you! Come to HIM!🙂🙂

THANK YOU SIR.

Super sir ,thank you 🙏🙏

Thanks much appreciated!I am hoping to figure out how to get the z coordinate? please!

Like the video Tom . I have to say myself that I usually pick up my X and Y Axis and input my offsets directly into the work offsets screen ( G54 , G55 , G56 ) etc... instead of using the realitive position screen . That eliminates having to input the numbers twice . Just quicker that way . Now I'm not using a electric edge finder . Because of you using a electric edge finder do you have to do it in that sequence ? I'm not sure you do .

If your using an edge finder why have the part offset to the left hand side in the jaws.....should be in the middle and you should set a stop up if it’s a batch run

Thanks Tom

Well done sir ,very useful thanks

Super

how to make a hole of the hexagon ?

This is a good refresher for me!!

Z ????

Clocking up that vice when you got it perfect is so satisfying

Kerusakan apanya ya.. Mesin miling dosan buat proses kok geser berubah ubah padahal klem atau kunci cak nya udah kuat

Z offset ????

THANK YOU SO MUCH TOM. God bless you!!

Very helpful, thanks.

Is Tom still alive? No videos in a long time

and the video for Z g54 and tools Len ?

tom, what mastercam should i install in my computer to start learning?

hello Tom, i am from VietNam, thank you , have a nice day

Thanks. Tom

excellent video

شكرا لك كثيرا صديقي

Is it me or does this guy sounds like Sean Connery?

thks

hello from colombia!!!
we have a problem with us DOOSAN. i set the offset with 2 different tools but when i test the first tool this goes to zero offset perfectly. but when i change to the secound tool this dosen't go to the Z possition that i had set. please help me!!

Thankyou sir for Shareing in this video....

you could touch off X axis and input x-.3 then set for the offset being used and it calculates automatically. Then touch off Y axis and set to y.3 and it calculates for the y automatically. I used .3 for half of the ball on the edge finder (.2) plus .1 for the material.

Ful name of ACT.F

Great explanation 👌👌👌👌👌👍

how to centre from edge by dial indicator please provide video

There are so many examples of how to do this on here and I have to say this is the best one of the lot for its clear and concise approach. Big thumbs up 👍

I informed to you that I have a chinese CNC milling machine Model No : WN-A850Z Fanuc controller. To changeAPC Battery of machine . referance point shifted. as a result of machine moment towerds X , Y axis is half reduced . So we can't operate the machine for full size towerds X , Y axis.

There fore please send a valuable suggestion to solve the problem'

Thanking you.