How to Repair Toilet Flapper and Flush Valve by Korky - 2003MP

How to Repair Toilet Flapper and Flush Valve by Korky - 2003MP

Korky Toilet Repair

5 лет назад

133,241 Просмотров

How to Repair Toilet Flapper and Flush Valve by Korky | Part number: 2003MP | https://www.korky.com/parts/flapper-seal-replacements-flush-valve-replacements/premium-universal-flush-valve-repair-kit

Hello, and welcome to Korky toilet repair. Today we are going to install your Korky Universal Flush Valve Repair Kit. The first step is to shut off the water supply to the toilet. Next, flush your toilet. Mark the water level in your tank and drain the excess water. Remove the old flapper. Clean the drain seat with steel wool, sandpaper, or an abrasive pad. Wipe all debris and moisture from the surface of the drain seat. Set the new seat upside down on a safe flat surface. Squeeze the silicone sealant evenly around the bottom of the seat. Use about ¾ of the tube. Center the new seat over the old drain seat and press firmly into place. Make sure to avoid getting and sealant on top of the new drain seat. Wait 15 minutes for the sealant to set completely. Install the Korky ultra saver flapper. Attach the flapper ears to the tabs on the flush valve. Attach the flapper chain to the flush lever with minimal slack. Turn the water supply on and wait for the tank to fill completely. Turn off the water supply and flush. If the water line drops within a half inch of the pencil mark, your installation is finished. If not rotate to the open position and reinstall the flapper. Turn the water supply on and let the tank fill completely. Turn off the water supply and flush. If your water line is still not within a half inch of the pencil mark, adjust the dial so the next lowest number aligns with the arrow. Then reinstall your flapper. Turn the water supply on and let the tank refill completely. Turn off the water supply and flush. Repeat this process until the water is within a half inch of the pencil mark. Congratulations you have just installed your Korky Universal Flush Valve Repair Kit. Thank you for choosing Korky.

Тэги:

#Toilet_flapper #toilet_flapper_valve #toilet_parts_flapper #toilet_flap #toilet_flapper_fluidmaster #how_to_fix_flapper #how_to_fix_flush_valve #toilet_flush_valve #leaking_flapper #running_toilet #how_to_fix_my_running_toilet #fix_flush_valve #fix_toilet_flapper
Ссылки и html тэги не поддерживаются


Комментарии:

@Strib420
@Strib420 - 17.12.2023 00:32

Bad results for me. Near impossible to get proper seal. Maybe in a lab.

Ответить
@aab2810
@aab2810 - 09.02.2023 07:32

Dear Korky Expert,
In none of your videos related to the flapper, have you explained whether to leave the hole in the flapper in "Open" position or "Closed" position, once the appropriate water level is achieved.

Ответить
@Ivan-nq9xj
@Ivan-nq9xj - 20.05.2022 07:48

I strongly recommend this product!

Ответить
@billschade1807
@billschade1807 - 17.03.2022 18:44

Replaced and still leaks. About a half inch in 5 minutes

Ответить
@TheJackPower
@TheJackPower - 23.02.2022 20:07

The flapper provided in this kit doen not fit a Kohler water saver tank, In fact, the Kohler flapper at Loews does not fit this tank either. Still trying to find a proper replacement.

Ответить
@elboregojhb
@elboregojhb - 21.07.2021 20:50

Replaced mine and it still leaks

Ответить
@carlitopascual9709
@carlitopascual9709 - 27.03.2021 05:36

Is this item available in the Philippines?

Ответить
@raymondbaumann2405
@raymondbaumann2405 - 09.02.2021 04:32

Gee I wish i could cut the tank like this so I fix this leaky flapper...

Ответить
@diem1836
@diem1836 - 20.12.2020 19:15

This used not to be so complicated. Oy.

Ответить
@gtrance3567
@gtrance3567 - 12.11.2020 21:00

So my seat kind of sits at an angle and the front part of it is almost flush with the bottom of the tank. Do you think this kit would work for that? Thank you

Ответить
@akbaahali8405
@akbaahali8405 - 11.10.2019 14:17

My toilet flapper seat does not have a rubber ring on it. Can this ring be added to stop flapper leak

Ответить