7 IMPORTANT MOWER MAINTENANCE ITEMS!  HOW TO GET IT READY FOR SPRING!

7 IMPORTANT MOWER MAINTENANCE ITEMS! HOW TO GET IT READY FOR SPRING!

markthomasbuilder

3 года назад

24,852 Просмотров

Ссылки и html тэги не поддерживаются


Комментарии:

@boots7859
@boots7859 - 16.04.2021 02:34

I would consider looking at the Project Farm Oil Showdown he did last year. Thats an aweful lot of money for some 4 stroke oil.

Ответить
@kingofthecrease30
@kingofthecrease30 - 16.04.2021 03:09

good video 👍 did you have to check the air pressure in the rear tires ?

Ответить
@konamanstudio2447
@konamanstudio2447 - 16.04.2021 04:16

🤩🍻🍺😊

Ответить
@arnilazarev1771
@arnilazarev1771 - 16.04.2021 05:22

🤔🤝🤝🤝😊😊😊👍👍👍 как всегда молодец!

Ответить
@anthonysmith9410
@anthonysmith9410 - 16.04.2021 12:22

Excellent maintenance video.......thanks

Ответить
@gfmclachlan
@gfmclachlan - 23.05.2021 15:28

Nice vid. So this unit nor the Zt150 doesn’t have any zerk fittings to grease?

Ответить
@dirtydon8661
@dirtydon8661 - 15.10.2021 04:10

I believe there are grease Zerks on the two front tires.

Ответить
@JA-wp6cj
@JA-wp6cj - 09.06.2022 01:43

Thanks for the video, just got a zt1 50. Not sure if it applies but my JD mentions timing your blades, basically one is installed 90 degrees the other -I

Ответить
@user-cb2427
@user-cb2427 - 29.09.2022 16:11

If you put two in the residual oil could take care of .1

Ответить
@whiskeytangofoxtrot4523
@whiskeytangofoxtrot4523 - 06.04.2023 17:23

Good detailed video. A suggestion of what I like doing for all oil changes I do is fill the oil filter with fresh oil before installing it so there aren't those few seconds of 'dry sump' while the oil pump fills the filter. When the filter is installed sideways, you can still fill it with oil, just don't fill it to the top. You'll be surprised how much oil gets absorbed by the filter element. I believe the cumulative wear after 5 or 6 oil changes with an empty filter would cause a decent amount of wear to the cylinder walls and to the piston rings.
Also, before installing the new filter, make sure the rubber gasket from the old filter came off when you remove the old filter. I've had the gasket remain on the block on the last 2 392 Mopar engines I've done oil changes on. If you don't realize the old gasket didn't come off and you install the new oil filter, you'll have a HUGE mess once that engine oil is up to full psi. Keep up the great informative videos.

Ответить
@HGAviator
@HGAviator - 11.07.2023 06:15

What tool brand did you use? I couldn't hear you. 😂

Ответить
@teztovar
@teztovar - 30.07.2023 09:11

Its not necessary to lock the blades with a piece of wood? Im about to swap mine out sometime next week for the first time.

Ответить
@Todd408.
@Todd408. - 31.07.2023 17:09

Don’t forget to grease where the front wheels connect to mower, same side as valve stem.

Ответить
@Roaming-Mike
@Roaming-Mike - 24.10.2023 23:53

Any grease points?

Ответить
@ntmd8or100
@ntmd8or100 - 24.05.2024 08:56

So, it's not necessary to lube grease fittings on a ZT1? This is video #5 that I have watched and no one does it.

Ответить
@brianbrink1421
@brianbrink1421 - 16.08.2024 10:44

R u a Milwaukee saleman??

Ответить
@MarkThomasBuilder
@MarkThomasBuilder - 16.04.2021 00:47

QUESTION OF THE DAY: Do you do all 7 items to your mower to get it ready for spring? What's your favorite mower, either commercial or residential? What's your favorite brand of engine?

Ответить