Eachine Wizard X220S - After 2 months - Part 5/5

What camera and goggles you use, dvr footage looks very clean

I think they upgraded the vtx and esc if I'm not wrong, I've had mine for 3 months now and it's still flying perfectly, I just have to get rid of propwash hahahah

what an amazing backdrop!

Hi can you send my by mail your betaflight configuration with a dump please ? ( [email protected])

Is this a stock wizard x220s or did you upgraded the faster rotors?

Hi what did you change about the drone?

Mr. Crowley and his drone

Hey fire, here is Made in Germany from the RC forum =). I own 3 of these older x220 F3, and i can say these motors also create bad yello and vibrations after a while of using. After some month, mine had the same crappy performance like shown in your vid.

I changed the motors to kingkong GT 2205- 2350 KV, and tryed these 2 stick commands for calibration (gyro and accelerator). After that it flys smooth again, even better then right out of the box. All settings are stock, stock ESC.

I fly FPV with the "eachine all in one VTX 02". No more worrys about interferences from the board, because it is a fully standalone system, powered by an extra 1S lipo =). I use it with the eachine V2 goggles. I get an amazing clear signal with that bundle, had a lot of fun in the last weeks.

Keep it in the air my friend ;-)

nice share!
EMF interference ...
Did you try to resoldering your old VTX especially the shield ?

interference in vtx with trotle this I know when antena is broken or conector from vtx to antena have broken conection

what does mean FM series at capacitor ? I think you have to use low ESR capacitor

How did you get rid of vibration?

Hello. Could You send me or write down below a final configuration of PID for this Quad ? I have this quad but i do not know anything about tuning PIDs yet :/ I would be very grateful.

Bottom barrel motors...

Did you change firmware at any time? I find in 3.2 d is to high on some of my rigs now. Try less d check gyro traces to see if it's noise on gyro if so it more issue in motor like bearing. Do you oil motors not all use sealed self lube? The vibes sound more mad d then p and by cutting p d does more work making it worse it also makes vtx dirty with spikes you might need to adjust filter in end but if you changed try stock or old good p and lower d

Hi
I see you have lots of experience with racing drones. I want to buy mini drone for up to £150 with good video range lets say 200-300m or maybe 500m if possible??? And good video quality, so im guessing I need good camera and goggles.
Doesn't have to be fastest drone but I want nice flyer and not to expensive :) . I already bought eachine vr011 they 5inch 800x480(not sure if i will get a good quality of those? But i don't want to spend 300£ for fatsharks ), also i already bought flat panel antenna and mushroom antenna to upgrade the range .
I bought flysky fs-i6 transmitter without receiver . Now my question is which of this mini drones will give me nice flying experience ?
I really have no idea what to get.
I know soldering and im good with diy , but im completely new to fpv . I was thinking to get fighter 130 and change the camera , antenna and receiver , but i don't know which ones to get, or maybe there are better options?
Do you mind to give me some advise ? Maybe on messenger if is too much here (my facebook account: DYMO Landscapes)
Anyone?
Thanks in advance

Nice flying mate...keep it up!

thats a shame, hope you find the cause soon, i'm sure a whole lot of noobs are scratching their heads on this kinda problem.

Thanks for the update. I suspect it has been crashed often as well, considering you often fly around trees. Maybe the bearings are still ok but there is some slight bend in the motor axles or some unbalance in the rotating motor housing, that holds the magnets.

At what power settting of the VTX do you fly? Could be the heat caused the board to deteriorate gradually. I often wonder how a VTX even survives, it often gets so hot and electronics don't like heat.

Ok the Jello isn't great but the VTX interference is crazy bad! I couldn't fly it like that at all!

Bearing ??