Комментарии:
I just listened to the latest Hackaday podcast, they featured your bobbin winder! !
ОтветитьVery nice , but can you not used PCB in your cool video ? I am very stuck with it (the PCB's)
(Can we just simply with arduino or simple kit board, even i know you are sponsored by the JLpcb, but please do not always with PCBs ) thanks :)
Good idea 💡
ОтветитьGood idea, amazing video
ОтветитьWhere to buy this table saw?
ОтветитьAWESOME!!!!!!!!! please make agricultural equipment (DIY)
ОтветитьEvery time when I see your videos I get to know about the technology in a different way.
Ответитьi really like the sensor at the bottom so that it doesn't waste any extra
ОтветитьИ на хрена это надо?
ОтветитьWhy doesn’t it feed a full label ?
The close-up shows it moving about half a label height.
Nice project
Ответитьit would be great getting it to automatically place a label, say on a glass jar. great project
ОтветитьNice project but the custom PCB burried it.
Ответить, tape support no costant speed.
Ответитьhow much you study
ОтветитьSir please give your whats up number.. I need your help
Ответить👏🏻👏🏻👏🏻
Ответитьvery good....👍
ОтветитьMr.Innovative other episode make an oxygen quality index,sorry if i have a mistake
ОтветитьNice job. Instead of measuring a length though, you might want to try a sensor like they use on commercial machines. Put a bright LED or laser under the label and a photoresistor above the label. Then measure for a change in luminosity. When the light is brighter, you know you're over the webbing instead of the label. Then you can use your knob to adjust the extra distance to unroll the label (instead of the entire label length), so you get the perfect tear off amount.
ОтветитьGreat work! Do you supply parts list and dimensions? Thanks
ОтветитьHow do you control the paper lenght to machine release? because this values change with the paper roll diameter.
Ответить33 people have no idea what a cool project is.
ОтветитьGreat work. As others have said, sensing the gap between labels is better. Over time, as you get more paper wound onto the motor spindle, the length of label dispensed per rotation will increase due to the diameter of the shaft increasing.
ОтветитьThank you man. Im just thinking how to make machine like this and YT suggested me this. Need little upgrade for size of rolls and its perfect
ОтветитьThats amazing video....
More innovatif come my home....
👍👌
ОтветитьBro pls make a 3d printed circular saw with 895 motor pls
ОтветитьHello.
Why is on your pcb an another stepper driver and two L293D is this for the next version? Next week I will build the machine hope it works 😅
I loved this man
ОтветитьWhere did you get the baby saw from ????
Ответитьhow can you repeat your project where to get the library and sketch thanks
Ответитьwhich diodes do you recommend it for D2 and D3?
ОтветитьIncredible! Minimalistic awesomeness: just the awesomeness!
ОтветитьHow is the LCD Display connected, it is not mentioned on the wiring diagram as well ?
ОтветитьPlease, don't stop your innovations.....!!
Thanks you.
Hello, where can I find the electronic components specification for the PCB, which diode, which transistor,... pls. advice, Thank you in advance!
ОтветитьHello, can I place a sensor to detect when someting passes the machine dispenses a label? And also can I change the motor speed?
Ответитьwtf is pcb
Ответитьcan you send the coding?
Ответитьbro can you send the file of PCB plz
ОтветитьHello, can you help and tell me where the parts are connected on the board.
When connecting the operating voltage what is there plus and minus
Kind regards
do u sell i need one. can u send it to chennai.
ОтветитьBest project
ОтветитьHii sir ye custom pcb kaise mangwaye nahi mil raha link send kardo plz sir 🙏🙏
ОтветитьWhere can I buy this project?! This works perfectly with my restaurant but I don’t have the time to make it. We need the DIY aesthetic
ОтветитьWhere can I get the file of pcb circuit board same as you😢
ОтветитьGreat project! My daughter and I are new to watching your projects and have really enjoyed them. We did have a couple of questions, what voltage and amperage power supply did you use to power the project, and is it possible to see an image of how you connected the LCD, Push Button, encoder, and IR sensor to the control board?
Ответить