OpenWRT - Install and Configure LTE modem in QMI mode - Quectel EC25 & Wallys DR4029

I have 2 module, run with qmi mode. How to load balance 2 module? There is no config for gateway metric in intrerface qmi.

What does this module actually do? Does it give 4g access to a router?

Hello...I just want to ask if the said tutorial is also applicable to ZTE 4G module...Thank you. By the way, the processor is Qualcomm...

Bạn chạy trên con modem gì thế . Này là làm sever à b

Bác chủ cho mình hỏi: mình làm theo clip tới bước minicom, thì gõ AT ko được, là do card wwan chưa unlock nên ko vào AT được? Chỉ khi unlock mới gõ vào AT ? Mình làm trên card em7455

Hi, your videos are treating several technical aspects which make them really interresting and a reference.
I found a module (HLK-7621A MT7621A) similar than the Wallys one and I would like to know if you have used it or if you can advice if it is possible to do the same thing using it like your Router (of cours with the same Quectel 4G mini PCI or similar) ? What should I take into account (image, compilation,...) when it comes to use another module or board as a router?
(info: it seems that the 7621A is based on OpenWrt and it is supported by OpenWrt)
Thank you.

My router got bricked while I tried this. Don't know what to do now.

HI, I'm from Brazil I have a we826 and I can't configure the 4g it's only on 3g, here it takes 2 frequencies of 4g

This is nice but like in many of your videos, this not working for many services provided in North America.

You cannot simply put any SIM card in any device and expecting an auto config from your router to do the magic trick for you with just basic APN details. It does not work in Canada.

Same goes for gpon from ISPs, MAC address of the gpon are used to secure a link so you can’t just put the fiber cable into any transceiver of your choice in hope to bypass your ISP equipment.

Hello how can i install a 5g module using openwrt

bác ơi có thể hướng dẫn giúp mình cấu hình cho card wwan chế độ MBIM k vậy ?

Hello. My router does not shows the device /dev/cdc-wdm0. I'm using a quectel ec25-AU in an OpenWrt 17.01 (lede-project) that I'm building using menuconfig.

Can this work for all modems with Qualcomm chipset?

How to managed openwrt router centrally, is there any NMS software or cetral controller software?

this support huawei usb modem?

Can the Banana Pi BPI-R2 Pro board work with Quectel Ec22 or EG25-G LTE 4G module ?

Great video. I am looking for a board for a T99W175 modem but that I can also run openwrt on.

Could you please make a video on how to use MBIM protocol also?

Can you help me configure 4g Vinaphone network?

Thank you for your video! I have a question: is it possible to set up a bridge configuration for qmi modem? We have a private 5G net and qmi works just fine, however I wasn't able to set up a bridge configuration using relayd.

I have gemtek outdoor unit router can change module chip for it please help

Phụ đề tiếng việt đi ông tui mù tiếng anh🤭

Please help to my tp link mr6400

5g sim card version available?

i am working on a project where we have ec25 cellmodems dying out in the field. Am tasked to find out why this is so. How do i go about this to test the hardware (does it involve writing code, if so, please some guidance.) . Thank you.

i have never used openwrt . iv used linux for 10 years but the routes are messed up out the box and eth0 never gains a ip and cant update opkg , set a static ip nothing add route to my home router nothing still cant ping anything disabled ipv6 nothing

How to know which modules will work with openwrt? Does the same criteria aplies to SFP modules?

Hello,
thank you very much for the nice tutorial. Do you know a good solution to automatically reconnect the modem? Because it doesn't reconnect after it loses the connection after 24 hours through a forced disconnection of the provider.

I can’t seem to download the packets. Can you help? When I connect to the command prompt I lose internet connection. I’ve downloaded the latest firmware.

sorry, but what is that used for ??

hi chào bạn, mình đang dùng padorabox, phát triển từ openwrt, lắp modem 4G sẵn, nhưng k phải hãng của Quectel , nó tự động nhận, nhưng tốc độ chỉ đạt < 10Mbps, kiểu 3g ý
bạn có thể cho mình ít thông tin hoặc trao đổi liên lạc được không

great tutorial! keep up with the good work! cheers

По этой инструкции если подключить модем, то он будет работать. Но! До истечения аренды IP адреса провайдера. Потом связь прерывается и надо вручную перезапускать роутер или интерфейс. В предыдущих версиях OpenWRT была поддержка "modemmanager" которая самостоятельно мониторила подключение, и делала перезапуск даже при зависании модема, сейчас надо руками из сырцов собирать, потому как ее больше нет в оф репозитории. Тогда вывод это хардкодить свои функции для мониторинга соединения и переподключения модема при окончании аренды IP адреса или зависании модема.

It works like a sharm, BUT when I reboot my rooter I lost the "Virtual dynamic interface" and I can't connet to internet. Anybody has the same issue?

hey thanks for the video.
i'm looking for a a low price router board with display (lvds or hdmi) and pcie for modem. Any tip?

Дорогой он стал на Aliexpress 3200 + 400 доставка, я неделю назад брал EP06-E за 2850р продавец ещё и пигтейлы в подарок положил. Ищите в Telegram магазин lt4220..

Hi, Thanks for the video explanation. I have a very simple question. I have router RUT500 by teltonika with HSPA+/3g/ mini-PCie modem. If I upgrade a modem in router to 4g/LTE module, then it will working without install OpenWRT system , with original firmware? Thank you and sorry for some stupid question.

Thanks for the video. I was able to find my mistake. It working now

Can the modem (quectel) itself get a signal, or do you need antenna?

thanks so much. Question: After installed all packages for EC25 qmi, openwrt web interface shows some information for 4G module in the overview tabs, like rssi, signal strength, isp, etc ?

thank you berfect

Hey man, thanks for the OpenWRT guides. Been a huge help for a complete newbie like me. I have a question though, is it possible to do LTE band locking on a built-in modem through OpenWRT and if so, how do I go about doing this? Sorry if this is a bad question and again, thanks a lot.

Hi Van, 1st of all, Thank you for your content! Quick question; I’m compiling my first flash file & would like to follow this tutorial but I’m having an issue when I run (make menuconfig)
I have WSL on Win10 PC & Ubuntu 20.04.. The issue is I’m getting an error reporting that I’m using a (relative path) in my $PATH but this no true. Some online forums say the reason is because of the (.) I.e. (dots) in the version name/ path naming convention.

Is there a workaround for this? Or should I use a dedicated physical machine to run its own version of Ubuntu 20.04???

Sorry for being so long winded in the comment section, but can’t find a solution for this problem. Thanks

This is new territory for me so any guidance you can provide would be greatly appreciated!!!

I seem cant opkg update..error code 7

Oa :v mới biết anh là người Việt Nam :3

I see you are running openwrt 19.07 did you build this is there a link do download with instructions or did you install the reference qcom DK04 build?

Your channel falled off eversince you run those sponsored videos