Homemade Vertical Wind Turbine From Barrels and Scooter Parts

If u make your wind turbine into an odd number of blades, it can be more consistent as it will not have counter wind force between opposite blades.

nice land man!!! dang!!

A few things use a flywheel to get the motor going and you would be perfect person to give me advice I want to build a windmill generator and I need to know what and where to find a highspeed gearbox I use scrap too so what can I get the gearbox from free or damn near

Wind generator here is a large land, I designed it bigger to get electricity and use electricity for heating.

It's possible low rpm AC wind turbine for home use, like synchronize 6 RPM Motor

its working in low wind speed 😊😊

GOOD JOB ! ;)

I love you from India Bangalore Karnataka

Hi How are you now

🎉parabéns!
Ótimo trabalho parabéns!!!😊

All practical tests show that small wind turbines hardly generate any electricity. Purchased turbines only at costs very significantly above 1$/kWh!
There is hardly any wind near the ground, and it is also very gusty, which extremely reduces the service life of the systems.
With solar systems, you can reliably generate electricity for about 7-12 cents/kWh over a period of 25 years!

Muy buen video graciad

Sir. what kindof circuit should be fix to charge the battery as battery current goes back to motor when wind doesn't have enough force to drive the blades as the battery voltage should not go to motor

How’s the wind turbine holding up?

A lawn mower engine? Would that work as well as a permanent low RPM generator?

Consider to possibly of making your own pirminent magnet alternator. Pericetic drag will be almost zero as there will be no brushes and comunintator. A few silicon diodes will get you dc. The more coils you wind the smoother your DC will be.

As a small wind turbine owner: the longest a small diy wind turbine is 1 and a half months (6 weeks)

I love your innovative approach to things. I used yo build & sell 1-3 kw wind turbines using pmgs. ,& bladr sets. Lost all my equipment facilities & spares Get it functional & then improve perfect it. just as i used to Are 24v-36v Scooter motors any use as PMA's. Or i may buy from China soon.

Lots of self deprecating humor, however nothing ventured, nothing gained. Most sit there arse on the couch. You are doing.

@saveitforparts >>> 👍👍

Use a multi Vee serpentine belt or a timing belt... MUCH less friction ...

😎👍☘️🍺

Am sorry but 5v out of the size of wind turbine which generates 1000 to 300w is so abysmal, the current might even be lower

Hi! New subscriber here.

How long did the turbine lasted? Did not find a follow up video.

Wow worst video I've watched yet

use a different transmission method. anything but vee belt, its the most inefficient. flat belt, toothed belt, friction wheels, chain... all vastly superior. especially if you actually add any tension as youre supposed to.

was always a fan of the VAWT but then i grew to hate them. i made a savonius out of drums, put much thought into it, always seriously disappointed.

differentials. you only ever get the difference between wind resistance of the two sides.

and they really only make any useful push for about 90-120 degrees of the full rotation anyway...

amusing that a vawt can act as a hawt but a hawt cant act as a vawt...

Using barrels was a good idea, but you should have looked at other vertical wind turbine designs, this is not very efficient, its like an old steam boat paddle... Also that loose belt is really getting on my nerves lol.

Turban? 😂 other than that, cool video!

Add a small boost converter

I love your " crime against engineering"!

It does not make power, it barely generates a bit of open circuir voltage. Where is the current measurement?

hey buddy good work ok watch my last video if you can make 10 volts you can use the step up controller that goes to 40 volts at 20 amps they sell them cheep on amazon - and yes 20 amps .and your good to go and charge a battery and then hook up a inverter . hope you try it ..


I just updated my wind mill to be more facing one direction , all about test dont let any one say shit at least your doing it peace

i cant get over how much u sound like saul goodman, but otherwise very well made video thx for uploading

will there be a update?

That's why horizontal turbines a better they have more torque to power through tough motors

"I made it work with a hammer".

Ah, a true engineer.

And you really should have a tight belt. Loose belts slip all the time, which causes power loss and increased wear and tear. I worked at Sears Parts & Service for a few years, and though I was only a counter person I picked up some technical tidbits like that.

Is the monorail yours?
Holy crap if it is!!!

And I think the Mark 2 wind turbine looks good.
☮

🤓So Much fun to watch you in action and love how positive you are about it all!!

What's up with way loose belt??? I don't understand you what so ever...

It's poor design because it's lazy.

Very interesting. Good project. I noticed that you had some sort of control panel with a monitor screen built into it in your shop. What is that?

"I made it work with a hammer".

OK... OK.... <subscribes>

The belt itself is causing a lot of resistance to spinning, try a dryer mini multi vee ( serpentine) belt

Search for Zoetrope wind turbine from Applied-Sciences. Great pdf download of plans. - Eric.

Amazing! I pulled the motor out of an abandoned treadmill for the very same idea. Got a nice pdf plan for a Savonius turbine. - Eric.

I think you should brace the blades, to avoid losing energy to flex and perhaps delay stress breaking

Looks great ,hope it works well for you .🌠🚂✈️💗🕊️

pretty lame but i like lame thanks