Recursive Routing + Failover - Mikrotik RouterOS v7

Great explanation, thank you!!!
Is it possible to check the gateway using bfd instead of ping, in the recursive route?

Can i use target scope 12 because everytime i use 11 route is unknown. ROS 7.9

Thank you very much, very helpful!

With this setup Is it possible to have both ISP active together and double the speed of the internet? please guide...

Thank you for your great explanation. what if we have a third or more wan... should we set target scope 12 for third wan?

Excellent explanation!!! Nice work, thank you so much

Really great video, I followed Mikrotik's official guide, yet I couldn't configure failover properly. This time I did it in less than 20 minutes. Thank you a lot!

Thanks for sharing this, very helpful for me

This is the best tutorial I've seen 👏 please make one about PCC load balancing on Router OS 7

Hey there, how's it going? I really appreciate your videos. Thank you so much for spending your time with us and teaching us. You are amazing! Grats 🎉

Great guide! Thanks! It works great for me on ROS 7.8. What if I don't have a standard GW for one of the ISPs? What should I add to the route? For example, I have Starlink on pass-through mode and I set a DHCP client for the ISP1 interface. How can I set the gateway from the DHCP client as a default route? Thanks in advance!

Thank you so much Sir! we saddly have poor explanations across the web about OS7. Can you help me with another? how to clean the Conntrack when Gateway changes? I do have VOIP services and, every time the gateway changes, I have some problems with authentication, so I have to clean the conntrack to force new authentication at provider. Thank You SO MUCH!

My compliments ! Very clear and simple explanation.

Hello Wilmer, this is a pretty great training. can we add a second set of addresses to be monitored in case the IP we're using becomes unreachable before we switch to the second ISP interface ?. Many thanks

Thank you so much , greetings from Chile

excelent 👏👏👏👏👏 thx

So good

What a wonderful explanation, it cleared all the doubts I had, besides simplifying the whole process, I am very grateful. Have a wonderful day.

Excelent! Thank You!

Mr.Wilmer From your experiense in Mikrotik can we merge two internet speed Connection...?
i mean if i have ether-1=8M
ether-2=8M
can i merge both of them so i get 16 M..?

Muchas gracias por el video.

Great lesson. Thank you coming from the Philippines.

Great video, explaining about how to router os choose the routes and emphasizing about scope helps me a lot, thanks

Thank you! Works great i found your video and you save me! now the office is running on two diferent fiber connections and having a starlinkas backup! that should give me peace of mind for ma upcoming vacations! again Thank you! you have a new subscriber!

Thank you
so on this way no need i think to add dns because it already added on router for each ISP
is it ok ? or i should add dns on ip/dns add dns

Great video sir. if I intend to combine 3 isps, for example three 500mb connections combined for 1.5gb availability on the router, can I assign distance of 1 to all the connections? if 1 connection breaks down, 2 will still work to provide 1gb availability for the system. I intend to use the recursive routing provided above but use a distance of 1 for all providers. will this work sir? there are pcc settings in the mangle to handle the traffic.

It was great helpful, I'm Brazilian and I didn't find any explanation on the sites in Brazil, thanks for you help me. Keep going.
I'm sorry my English is not good.

Thanks, like.
It works great in RouterOS 7.5, though that screen refresh bug is still there.
Tip: you can use Netwatch to clear existing connections when the routes swap is done, to speed up the transition.

Hello, is there a way not to wait 20 seconds to lose 2 pings ? I need something faster ?

Hi! Thanks!
I was only able to do Recursive failover in this new version 7 with your explanation.
I updated my equipment to 7.5 and I was not able to do it.
In version 6.49 the default route I kept with the same scope as the monitoring route Ex:10 and it worked, now in the new version the scope should be bigger.
Thanks!

How do we check host to monitor ISP IP?

Excelente . Gratitude

Great job, thank you very much !!

Need a video showing how to do this with ISP dynamically assigned addresses.

I followed your scope/target scope settings but does not seem to reach the gateway. The immediate gateway status is just unknown. Does the scope and target scope change if I have more than 2 WANs?

Excelente vídeo! First video about this.

Gracias Wilmer, ahora podré usar mi RB5009 como balanceador

Could you please supply the EVE-ng file of your project? It could help us to better figure it up. Thanks.

brother kindly make policy base routing with recursive routing

Thank you very much for this. All working great in my site.

sir hotspot user connected but can't able to access internet when i go to hotspot host here i remove user mac address then again user can access internet soloution please?

HUGE THANK YOU! Spent a lot of time thinking that the target-scope should be equal to scope. That changed on the RouterOS v7. Thank you very much! :)

Great video Wilmer, once again thanks for your generosity, this confirm that i do not make a misstake on buying your curses. Regards

Thank you so much for this tutorial. A big help for my network.

Thanks for the great video, not only explaining failover routing in RouterOS, but also highlighting the change in getting recursive routing to work properly in ROS7! 👍 I also hadn't previously noticed the new check-gateway options... definitely going to have to dig into those.

Hi sir! Im studying this vid,. in this setup is there anything to config in mangle rules? I just want to implement this setup with my rb5009 running dual isp with pppoe/hs same interface can u give m idea how can i config this one... tia sir

Very cool videos on your channel :)!

can we use Recursive Routing + Failover with load balancing setting, if yes then how setup mangle rule for load balancing with recursive routing. can we use both load balance + recursive routing. Plz help me or send me full script, Thanks & Regards

How bout setting up failover based on latency sir? Lets say my isp has high latency/ping or is slow,for example my isp1 has 50ms or higher ping and need to route traffic to my isp2. Thank you very much sir