Transformer Parts and Functions

Great video !!! . Please keep up the good work !!!!

Tq so much

Dear sir
Pl show the slides what you are speaking

Very useful..thank you..

🍆🍆🗡️

It explaination with 3d animation is very informative with reliable understand..... Thanks for this video about transformer.....

Buen trabajo.
Los estudiantes de CEE115, debe deja un menaje en este vídeo.
Indicar su número de asistencia.
Saludos.

Great video as usual 👌👌.

if a small fault continues, in this case, as the volume of gas in the gas relay increases, will the transformer open

nice

Well explained. Thank you.

Great explanation

Wow besr

INDEED, THIS IS GOOD INFORMATION !

nice
ty

Great presentation. Thanks for this.

🙏thanks you

Sir transformers banane vali company me Mechanical engineering ki kaya jarurat hoti he
Or usme production planning and control department me Mechanical jaa sakta he

Great video indeed as many others have said. BUT there's only one major component that wasn't mentioned and I only know cuz I work in the utility industry. The CTs that are wrapped around the bushings. Very important piece to monitor the current flowing in and out of the transformer. And for protection.

You kept saying that if the level of oil gets too low, it causes a catastrophic failure. But why??

Great video, very clear and informative

I want you to know... I'm learning a lot about transformers. Thank you for your expertise.

Good work

Add PRV working .

You are the best

I like the video. thanks for sharing

Very nice gas

Very nice introduction. A good supplemental video project could be made on Grids and Transport.
Air/sub soil/sub sea line systems, TN´s, TT, IT and so.

We have a factory that requires 6 MVA electric power , Can we use one large transformer and limit the fault current with NGR?
our transformer is
11/0.4 KV

Sir,Which software you had used for designing this model??

❤️❤️🇧🇩

I am a lowly 'low volt' (120/240v 1ph; and 3ph) residential and commercial (some industrial) electrician in South Florida. This is the first time I have really read/seen/heard ANY detailed information on transformers and their design and operational characteristics. Very, very interesting, entertaining and informative.

Thank you.

There is a guy named Mousa Al Manasif [2 years ago, from now 01/02/2022[], who complemented and thank for this presentation - but brought up a few things where he says there were a few incorrect statements made in this video concerning:
"However I noticed two things that are incorrect:
1- OLTC on load tap changes are divided to two parts
a. Diverter switch ( the arcing and the interpretation of the current, have separate compartment)
b. selector switch ( the part inside the TR main tank which shares the same oil of the TR)
OLTC diverter switches ( are always separate from the TR main tank

2- At the end of the video OT ( oil temperature gage) the red Needle is only a memory needle to show the highest temperature recorded by the OT.
When the black needle ( showing actual temperature) moves up it will move the red needle along with it but when the temperature goes down the black needle will go down the red needle will stay at the maximum temperature the OT recorded so operator can see it during there inspection".

Could you comment on this. And if he was correct: Are you looking to create a revised version of this video; or add an addendum that addresses these things one way or the other?

Either way, the video was superbly done.. Thank you again.

thanks sir

អគុណបងthank

Fantastic video...puts my lecturers to shame

Good one

Thank you. Super helpful!

Hi friend
Wich program you make it??

Very nice and helpful video for us, because we manufacture oil filtration machines and oil testers for transformers.

There is insulator between the HV windings and LV windings, this could be shown

Great job bro

Thank you for a most informative explanation well presented.

brilliantly explained!!

This is helpful.
regaurds.

great starter video

Excuse me Sir, can you explain us about High series capacitance winding ? Which is used in power transformers windings, exactly in High voltage windings. With my best regards.