Комментарии:
If i find any other video like this on your channel, i will do "don't recommend this channel "
ОтветитьFicou feio demais! Prefiro ga$tar um pouco mais!
ОтветитьI'd rather pay. It is ugly looking and it might compromise the thickness/integrity of the pipe. Haha
ОтветитьOnly idiots do that 😂
ОтветитьBeen a plumber all my life and this not something I would do or have ever done . This guy is just cutting corners what a shady Plummer you are.
ОтветитьYou both are wrong. You should have shortened the distance and dug the dirt
ОтветитьТруба какая то странная. Это не полипропиленовая труба под воду, а круглый кабель-канал под электропроводку. Уголки в нем соединяются без пайки и настолько копеечные, что экономить на них... все равно что стирать и штопать презервативы.
ОтветитьHabiendo codos en este tiempo voy a estar haciendo esas tonterías.
ОтветитьThis is a great commercial for plumbing connections
ОтветитьThat was not good...
ОтветитьYou can do it better to reduce dragging (pressure-losses).
Since a cheap elbow has a very short radius to form 90 degrees, you can make a longer radius.
By doing this, you would have a smooth round (very limited wrinkles).
Я бы экономил время
ОтветитьLol imagine yr upmarket home with joints like that!😂
ОтветитьWhat an idiotic idea. You'll have a weak bend, since you can't control the wall thickness, and you'll spend FAR more time committing this idiocy than if you had just done it correctly with elbows.
ОтветитьKoji ti cirkus radis ai ono je tocno
ОтветитьWay way to much work
ОтветитьTravail d'arabe, il aurait dû laisser les coudes , sont intervention est nule à chier, espérant que ce guignol n'est pas artisan .
Au lieu de faire une vidéo, qu'il aille planter des carottes si il en est capable.
Foolish creativity. Wasting time. Not properly connected.
ОтветитьWow..
ОтветитьCongrats 👏👏
You just saved 3 dollars .
I'll just buy the 49 cent elbows and be done.
Ответитьto nechceš.
to je debilita
hnus
Pakistani technology 🙄 👎
ОтветитьThis is a very stupid idea. 👎👎👎
ОтветитьIll spend the few dollars on an elbow.
ОтветитьLooks a complete mess and took way too long to achieve that mess. Elbows all the way!
ОтветитьWhat is the point?I guess if you can’t buy any elbows..
ОтветитьThumbs down from me, just a waste of time.
ОтветитьOrrible
ОтветитьDont use lbow, use bent
ОтветитьIts just a pipe dream.
ОтветитьI'd rather use the elbow, it's easier to do and it doesn't cost much
ОтветитьAmateurhaft , Schrott keine Ahnung vom Rohrleitungsbau.
Ответитьnothing is foolproof because fools are so ingenious
ОтветитьNo sabes doblar tubos mi compa
ОтветитьWhat a terrible music!!!!!!
ОтветитьThat's so wrong
Ответитьla musica es perfecta mente inconveniente.
Ответитьpinshe trabajo tan puerco
ОтветитьWas better with elbows
ОтветитьEse tubo es eléctrico
ОтветитьIl faut utiliser matériel du pl ce n'est pas n'importe quoi
ОтветитьProbably does plumbing for Mickey Mouse Construction.
ОтветитьVery wrong idea!
ОтветитьI think cost saving should not avoid speeding when changing or replacing a part, because you could also do one single piece but, is it required?
ОтветитьElbows will live longer and endure more stress and allow water to flow faster than these bended tubes, they are not even 85% straight and these micro curves on the inner surface will cause turbulence special with the speed the water is flowing in, it's a great hack if you have time and don't have money but nothing more C+ for effort.
ОтветитьHorrable job
Ответитьand now it cant be used for anything else
ОтветитьIt might get dry. And the kids might pull it out. My is with the one that are removed and it glued strong
ОтветитьWow much better to not use it and keep it always secret
Ответить