Ubiquiti Edge Full Setup and Configuration For Home Or Small Business

Way too fast for basic users

can you help me

Thank you - very helpful video!

Good God this is so helpful. Thank you so much for taking the time to make this; much appreciated

My ISP uses pppoe, I have setup the router for this with no DHCP server, but now I want to setup a UniFi AP. What steps would I have to follow to get it working in that scenario?

Thanks! Literally saved me hours to get this going

Nice video. I think I did pretty much that but without denying inter VLAN routing. Because I'm not yet sure if I'm going to keep the VLANS as they are. Though during my setup I had the issue, that I couldn't connect from the default LAN to the VLANs and I think found somewhere the answer that there is an issue and that I need to configure the default LAN as a VLAN too and remove the IP from the switch0. As I set the VLAN1 and added the default IP there it worked for me but I'm not sure if this is now preventing me from configuring L2TP VPN correctly. did you set up L2TP with VLANS? I tried setting the VLAN DHCP pool to a completely different subnet and I couldn't connect and when configuring an IP pool in the default subnet but outside the default pool I got the same issue. Thanks for any advice!

a bit fast but clear over all.

Finally, a comprehensive tutorial! 👍🏆

I am extremely thankful that you have this video. I am redoing my network, trying to simplify and remove items that are not necessary and didn't know how to work unifi with the edgerouter. Everything works well now and I just wanted to say thank you.

Love your video, it is very intuitive and useful, but can you do a video on how can we properly setup IPv6 on edge router?

I have edgerouter x, wan is incoming on eth0 on vlan1, and I also want to use the same interface eth0 for vlan10 in both directions to have a lan with network 192.168.2.xx.. I have tried everything.. I get the dhcp to give out adresses on eth0 to the switch on the other side.. but I can't seem to get access for the vlan10 on the local ports on edgerouter x.. is this impossible?

would the connection to the internet be an ethernet cable to your isp gateway?

I have a similar setup ER4 and Edgeswitch 24 lite. How do you ge the switch0 interface to show up on the ER dashboard? My setup works but I don’t have the switch0 showing so I don’t think I have my vlans configured properly. Thanks

I’m trying to setup ddns on my edge router x and when I save and check the configs it says other insted of eth0 and I have tryed setting it up over 50 times and it does the same thing so I’m wondering how do I fix it

My new edge router X here's to be working I'm logged into the dashboard but I cannot see any web traffic or CPU usage it is as tho nothings working but it is working. ? I'm confused what's wrong? any help?

Hi Sir, can i contact you, i need some guidance in configuring EdgeRouter X Sfp

Is it possible to install the Edge Switch to a Linksys router?

Hey! So, I noticed in the switch VLAN configuration, you didn't check any Trunk Port boxes, why is that? I was thinking you would have checked that for Port 1 if that's the port moving your three VLANs between the router and the switch...

Great video! I will need to watch about 7 more times. Will this router work well for implementing into a small IP Camera network that utilizes a Cloud based NVR platform?

Hi Cody, Just what I have been looking for. Keep up the good work

Thank you for this super-helpful video! It couldn't be more clearly explained - Best regards!

Loved the explanation. Didn't see anything about the admin network.

If I connect an edgeswitch 8 to a udm pro port profiles All, would the switch pass or strip the vlans that exist on udmpro

hi there hope all is well, i followed this video and the network is set and working as per your video. I have a vlan 10 as the main network how would i go about allowing that vlan access to management on vlan 1.

Brilliant video mate - very helpful! This is exactly what I want to do to my home setup before I buy the edge router.

Is the Edge switch 10x required in this setup? Can the Edge Router X handle the switching for the VLAN's and you trunk a port through to the AP AC and let that handle the wireless networks?

Great Job on the video's. Do you have any plans for short video on the Edgerouter 12? or maybe put me in the right directions on simple setup with few VLANS. Thanks

many thanks !!!

Any tips on how to get the LAG working with Windows NIC Teaming? I can team the NICs, and that seems to work and my motherboard has 2 NICs -- but if i add both those ports to a LAG on the edgeswitch (no matter the settings, static vs STP with or without DHCP snooping) then the windows network stops working.

So helpful thanks.

On the switch side, why didn’t you need to configure the first port as a trunk port. Is it because of making the router switch VLAN aware?

Hey Cody, Good job excellent detail on the EdgeRouter X and EdgeSwitch 10X. I actually have one of each of these and you covered the whole gambit of what I needed to do. I am sure I can get it all ready to rock now. Thank you again Out-Standing Video!

FIREWALL TUTORIAL FOR FREE!!! Big Thank u!

Really enjoyed this video the only part of it I don’t have yet is a switch but everything else is the same equipment

Simple and to the point. Nice job.

You are the man .. !!! you are unstoppable with your excellent videos. We will have to invent you a nickname of a superhero, SuperMacTelecom? Naaa, wearing the underpants on the outside is not his style .. !!! who gives me a better name for Cody?

Well done! If you had a choice for home networks, would UniFi be your choice vs. Edge?

Great Work 🤜🏻🤛

I love your Full Setup videos. Good job Bro