Round Pipe Bending Mistake // Round Pipe Bending Tricks

Machine ka naam kya hai

Goodd

Ye 75 gaje ka pipe hai 😂😂

'smooth bend
I'd grease up all the moving parts.

это для толсто стенного мать вашу

Thank You very much MD KHAN!!
May God give you more blessing!!
❤️❤️

Mental

સરસ સરળ અને ઉપયોગી આજ રીતે પ્લાસ્કિટ પાઇપ માં માટી નાખી બહાર થી હોટ ઘન વડે સરળ તાથી બેન્ડ કરી શકાય છે આભાર

You gotta fill it up with sand.

Best bending

You need to fill sand to be successful, that is because your technology is not good, so how much time will be wasted. You don’t need to fill sand, just change the shape of the mold groove and you can bend successfully.

первая труба была с тонкой стенкой ) а у второй стенка толще) и согнуть ее без вмятин проще ) засыпь песок в первую трубу и посмотрим на результат)))))))))))

Our dyed-in-the-wool " skilled workers " God forbid they come to Europe too.

Good job; congratulations.

What a waste of time. With proper tool you can bend even 0.45mm thick tubes without shrink. We are doing it in hundreds daily

Super

Bravo! Great!

Will any sand do?

Wwwwwoooowww !!! So amazing 😍 I haven't seen anything like it. You guys ROCK!

सिल्वर पाइप की मोच कसे निकले

Use bol medarl

The pipe which came out with fine bended is thicker than the previous one which was very thin but the guy did not show the thickness of the pipe but for first pipe he showed that it was thin

आप अपना मोबाइल नंबर सेंड करें

Kitne gaje Ka pipe hai

great idea

这个我以前弯酒管永的设备

يوجد افضل من هذا

Nice very 👍🏻

Awesome

Hi, Why you do not use Mandrel for tube bending? it's very simple.

I wonder if compressed air would work the same

Bhia circle ka size kitna hai

Si tienes. Que hacer 100 tubos te lleva meses con ese sistema buena esa felicidades

Nice thank you very much👍👍👍

Segala pake pasir ..bikin rumit aja ..ngak praktis...alat kurang mantap..

Muy buen consejo utilizar arena para que no se desfigure el tubo... desde Colombia

Very good - thanks

Genius

Geniuses

We need wheel of dye

kalokohan, minipis yung unang tubo, yung pangalawa ay makapal at stainless pa

Are Naas he kar daya katye

First tube was thin wall aluminum.
Second tube was thicker wall stainless. (You can tell by the color of the weld)
I call BS using sand without capping the ends TIGHT.

I don't understand how that worked. When I use sand I have to crimp the end of the tube off or it'll simply push the sand out of the way. This is for things like a brake line or gasoline line and making those tight corners.

Не правильно собрана. Можно без песка

Какая толщина стенки трубы?

Если немного доработать приспособление то можно без песка обойтись.

Add grease to the follower and it should improve a little

Getting the rags and sand out is even more difficult. A better way is to heat the metal red hot then bend it. Much better method

That first piece of tube was simply too thin to bend. The second piece was better. Sand filling helps but the stretch weakens the tube bif time. IF the end was not clamped so hard it would have bent a bit nicer