Fix Samsung Washing Machine Error 4E problem with Water Inlet and Sensor Water Level

How I solved the 4E error:

The symptoms were the error code appeared when the drum was filling. I followed the steps in this video but still no success.

I solved the problem by adjusting the screw you can see on the top of the sensor. I figured out that this screw depresses a spring which controls the water level / pressure. The tighter the screw, the tighter the spring, the more water the machine demands. If the spring is too tight, the inlet hose can’t supply as much water as the machine is demanding and you get the 4E (low flow) error code. With your machine unplugged, loosen the screw a quarter or half turn and the machine will demand less water and the 4E error should not occur. You may need to loosen another quarter or half turn until you find the correct adjustment through trial and error.

I’m guessing the issue occurs if the mains water pressure is slightly lower than the machine is calibrated for, so you have to recalibrate the sensor so that the machine demands less water / fills at a slightly slower rate.

Tnx

Just tried it and worked. Thx a lot 😀😀

Thanks 4E error fixed

Thank You very much very simply explained the problem and solution.

Mine started working after I checked these issues.... model number WA50T5300AC/US

Amen ✊😎

Thanks 👍

My washer is not sending a fill voltage to the filler solinide what could be the problem?

Same probelm

Anyone here know about the error dE door error.. my samsung is wd106uhsawq i close the damn door and a few secods pi pi pi and dont start i have to give little punches in the zone of the door i think is the sensor of door

Door sensor magnet

Well....tq for your support..

That's great video. It helped my problem. The issue is the water inlet valve sensor came up, so after detecting low water pressor the 4E appears. I just tighten and screw down (with spring) the sensor for my washer and it worked like a charm. Thank you

What will be the cost of the sensor if we have to replace it?

in my washing machine water is directly going to drain as soon as i turn it on it is not filling...what can i do?

Thank you so much.

Halo mas. Mesin saya baru tuker pcb (copy ori). Masalahnya mesin udah gak auto detect berat cucian seperti sebelumnya.. Tiap kali nyuci, startnya mesti dari level air extra low. Itu kenapa ya mas?

thee was no 4e on my list

Thanks man, your are a life saver.......
It was the rare case, problem with pipe of water level sensor...... just removed (like you showed) saw nothing wrong or bended and put it back and.... try ... WORKING.......

thanks a lot bang..., very helpful video... there is literally bug in my sensor pipe... i dont know where it come from...

My Samsung top loader washing machine is not draining the water, any surgestions of how to fix it

Life Saver. 🙏🏽🤗

Boss pano pag walang tone pano i activate

Very nice place keep it up 👌👏👏

Thankss

thanks , it worked

OMG thank you I kept thinking it was unbalanced so i would go out move clothes around and it would still keep beeping .

Thanks for the video 👍🏾
Turns out my machine is fine... frozen pipe due to winter storm, I know it sounds silly but I live in central TX and this is the first time it’s been single digit temperatures ( 23 high/ 4 low) in the 20+ yrs I’ve lived here ( the laundry and front yard faucets where the only ones that froze)
Good luck to all

Thanks for the post, my Samsung WA45H7000A was showing 4E and spilling water. When I investigated the sensor tube, as you suggested, it was not kinked; I followed the tube to its connection to the tub and found that it was disconnected. The tub would fill to sensor level connection and then invoke the 4E code while allowing the water to spill out the connection. My guess is that an off-balance load shifted the tub so wildly that the level sensor tube popped off; there was only a wire tie holding it above the connection, the tube had a spring clamp to hold it to the tub connection.

Hi there: Thanks for the informative video. I had the dreaded 4E error code of death. All the supply hose screens were clear, removable ones and inner ones. Taps wide open. Lots of pressure and flow out of the hoses. Still no luck. So I inspected the hose that leads from the bottom of the drum up to the pressure sensor. I found some chaffing part way up where the rib on the drum was rubbing on the hose and found a small hole in the worn area. I repaired this by cutting out the damaged area and replacing with a small piece of metal brake line. It would be best to replace the whole rubber hose with new but I don't have any hose in my shop that will work. Hope this helps some of you. Cheers

Thank you! For anyone else with the same model as me, the WA45H700AW/A2, this was the solution that worked for me. I first tried the suggested water screen cleaning, but saw this video, popped open the back, and sure enough the tube was off the spout. There was also some lubricant on the tube that may have helped it slip off, so I dried off any excess lubricant and plugged the tube back in and tightened the metal lock.

Thanks for this useful information it helped me to solve my problem , my filter was clogged and after cleaning it my washing machine is working perfectly

Hi brother plz can u advise me. Regarding 4E error bc my machine not stopping water in dram. Its going directly to the draninnage pipe. Kindly can u tell me why and wht will b the major problem. Bc i start using this machine after long time. Thank u waiting for response

Please my Samsung washing machine has 4e error code but still fill when using quick wash program but not other washing program. The error code is displayed when using any other washing program apart from quick wash. I have checked the inlet hose filter and water pressure, both appear okay. Could the problem be the inlet valve or motherboard issue. Any help will be greatly appreciated.

السلام عليكم عطل 4E كل شي تمام
تعمل الغسالة وينزل الماء ولوحدها تقف ويخرج هذا الرمز 4E
ينزل ماء قليل من اسفل الغسالة
بعد التوقف
وحاير ما اعرف الحل ارجو التوضيح
واذا اكو مصلح ارجو ارسال رقمه وانا من العراق بغداد وانا الممنون

Hi bro after changing sensor also problem not fixed

Thank u bro... I face same problem on my singer washing mashing & i fixd this problem after watching u r vedio...
Lots of love for u from Bangladesh ❤❤❤

Sir all Samsung washing machine brand, thier water inlet valve coil are 220 volts? Thank you

sent it to my dad!! TYSM!! it been annoying me n this helps ty <3

Pls I noticed that when my 15kg spins, the drum doesn't spin like it should. What do I do?

Mas... Mesin cuci saya air inletnya hidup terus. Saya cek pakai multimeter dia terus2an dapat tegangan 220v. Fungsi mencuci normal. Kira2 apa yg rusak ya mas. Saya yakin bukan water level sensornya yg rusak. Soalnya bisa mencuci sesuai dengan level air. Tp ya itu air masuk terus. Jadi harus ditungguin kalo mencuci agar air tidak kepenuhan

I switch my washing mashing to hot water insert of cold water and the 4E sign came up what should I do?

It really helped. Cheers mate 🥂

In my case it was that the drainage hose had fallen down below the drum water level resulting in the drum never filling to the required level. Once the drain hose was lifted above the drum level - no more error! Happy days!

Me and my dad been wondering what 4E is so I found the video and fix my machine 🤪

Thanks a Lot . It has really helped. Our Filter was fully clogged and hence the flow was minimal. Now working perfect.

Wow, you just saved me a good amount. Rats got into my washing machine and cut that water pressure tube. I reconnected and it's working like a charm now.
Thanks a lot Sir!!!

Hi sir one issue pleasle update me samsung top load pcb not work properly pcb is on but when i press start buton double beep come and not take any command ....plz solutions contact me or whatsup me 9741582743

Thank you it help me a lot