Тэги:
#jump_starter_powerpack_manual #powerpack_jump_starter #powerpack_12v_jump_starter #jump_start_power_pack #jumpstart_car_battery #jumpstart_car_how #jump_start_car_alone #jumpstart_a_car_battery #jump_start_car_correctly #jump_start_car_dead_battery #jump_start_car_engine #jumpstart_car_for_dummies #can_i_jump_start_a_car #jump_start_car_without_jumper_cablesКомментарии:
And keep the charger kit there????
ОтветитьWhen you connect to the battery.....will the battery test indicator tell you if the battery is charged or is that only to see if the power pack is charged?
ОтветитьIt says on it to not connect the black clamp to the negative terminal!!!
ОтветитьTHANK YOU!!!
ОтветитьThis is super helpful! Thanks!
ОтветитьThat shit is bad thing to charger
ОтветитьSweet & simple great vid
ОтветитьThe directions on my Cen-Tec portable power pack says not to put the black clamp to the battery; but to clamp it to grounded metal under the hood!
ОтветитьThank you for showing how to use the jumpstart cables but I need to know how to safely put air in my tire.
ОтветитьI know that part,lost instru tions
ОтветитьIf it still don't start and a red light comes on and a high frequency pitch then what?
ОтветитьListen guys!!! After trying or following the Centech instructions, my car still won’t start!
For the third try i decided to connect black clamp to the negative pole and it worked!
mine started fast. thumbs up. ground car on something else besides _ negative battery post. use some exposed metal on engine. positive must go on battery. make sure they are both snug and jumper is charged up fully. hook it up for 5 mins with power switch on. ignition switch off!.) after starting disconnect it by_( turning off jumper switch. remove negative- black. then remove red+ positive. leave car running and drive some. charge unit when you get home.
ОтветитьI thought it says to put black ( ground) clamp to a ground on metal part on car engine area. ? mine worked this way. but it first time sparked on me. scared me. it must been poor ground and I have those tiny side terminals which I dislike. so glad this seems a good jumper and didn't mess anything up. ez to use.
ОтветитьThank you for making this short and to the point I hate all these review people who do 7 mins vídeos talking so much like shut uo and show me
ОтветитьLove it BUT!!!! It's useless on filling air on my avalanche lol I waited ten minutes and nothing but the motor 😆
ОтветитьWill it still work if I turn on the switch on the back because I don’t believe it will as I thought mine was broken because it was making a lot of sound and it wasn’t charging shit
ОтветитьThanks! Quick video a life saver!
ОтветитьIt says in the instructions NOT to connect the black clamp to the negative battery terminal, but rather to a non-moving metal chassis location. Also says you must WAIT 5 minutes after connecting or the car may not start.
ОтветитьSeems easy... I'm about to go try this cause hubby is at work and I need to crank my car. Girl power!!! Maybe... We'll see... 💁🤞🤞🤞😅
ОтветитьLiterally just had to start my car with my Centech, this thing is fantastic
ОтветитьSo helpful
ОтветитьCan I use this to power an LED light 100-240v for outside lighting do I need a power converter strip and what brand?
ОтветитьUhhh you need to wait 10min after hooking up this booster pack before starting the vehicle. Says so right in the instructions
ОтветитьThe safety instructions on this says to put the negative on another piece of metal. I thought like this guy too.
ОтветитьThank you for such a SENSIBLE and PRACTICAL demonstration!! :-))
Ответитьsafer to conn3ct the nagative to Tue Chassis isn't it?
ОтветитьGreat video simple and to the point
Ответить