2 Clicks Out: 135 vs 235 pound Rider (60 vs 105 kg) Suspension Setup Intro

the screwdriver and hammer method, I love it! :)

Im 5-10 270 freedom units (stalky, certainly not obese). Tf am I supposed to do?😂

-The ignorant coward is wearing a muzzle, he must have had some vaccinations💉💉💉 too,,,🤣...and some will still say that riding a motorcycle is dangerous....

You look like a top notch motorbike coach here. Good common sense explanations. Nice work, thanks for the vid. Liked and subbed.

I would love this service! Are you still providing then?

I especially like Dave because of his mask less attitude.

Im 265 so im assuming i should just max it all out? Lol

this is so important..i worked for buell and funny how only woman who wanted the lower seat Buell CG would get preload sag adjusted and asked me to adjust it for them.

I have a 22 sportster s and I feel like it’s too stiff on the highway it feels like I have no suspension it feels super bouncy like if it’s just hopping everywhere I tried adjusting my preload and damping from Harley’s manual to there recommendations but I feel it didn’t help 😭can someone help 😢

to Max VA Disability - I cannot access your comment. So here is your reply: set fork preload with 4 lines showing and damping at 6 clicks from maximum. Use a cable tie to get fork travel at 10-20mm from the bottom of the chrome tube via preload.

I weight 145 so very close to that guys weight.

Guys like this are annoying

Guy works his ass off at sanoma. Non stop bikes and he nails it at every level. Great man

Huh ... 67 bikes a day?

hy Dave .. i realy like your videos. i ned a litle help ..i have a 2021 cb650r and i cant rode my front whel is like 2 cm each side but the rear whel is just fin i rode all rubber of the whell ... the rear suspension is a clasic whit 10 nivel spring compresion ..... the front fork is not ajustable ..

These videos are basically just a waste of time...
If you want views and subscribers you need full length videos with actual content.
This isn't 2005, trying to get people to move over to another site to pay for content isn't a very good strategy.

You would be alot better off offering more complete content and then advertising your in person services.

Im watching dave moss videos over and over again...

My RE Continental Gt650 cafe has a buttery uneven forks.that wobbles when I corner, like a lot! Bouncy

I'm 666 on here

I live in NYC , where are you located DMT ?

I didn't catch street riding psi on the heavier rider. I'm around 240lbs riding an 16 r6. Just curious about the psi for street riding from a real pro. Great vids

I love bmw s1000rr but seat height is a little bit height and I'm 170 cm. Is it possible to lowar bike like 2 cm?😊

Kilograms, now we're talking.! Greetings from Mexico.!!

Hi Dave
For me my bike is 2017 zx636 use tyre S22 and my weight is around 80kg how much for front and rear tyre pressure?

Dude, a ball-peen hammer and a screwdriver?

What tire pressure is good for Daytona 675 r on track for 90 kg guy? U have great channel

Hey Dave I have a doubt about my duke suspension. My bike ground clearance is not enough for me(in India) 155mm. so i decided to tight my rear shock absorber. I thick it may help me to prevent from hitting in speed breakers.when I raid with pilion it hits always,without pilion it doesn't hit.if I tight the suspension to 10th step, it reduce the issue and also affect the suspension life???????

Informative as always! Respect from India.

I think kawasaki may have heard you, adjusting my z900 was easy!

Before attending Dave's tuning session in Thousand Oaks last week I had given up on finding a good balanced setup and was ready to buy an aftermarket shock and springs. But a few minutes under the DMT tent answering his questions then making adjustments put this motorcycle RIGHT. The front - rear balance he obtained with stock suspension is remarkable. Controlled and still compliant. More confidence, more fun, more chores getting put off because I wanna go riding!

Great quote in the intro Dave............"No motorcycle's suspension off the showroom floor is setup correctly for any rider much less every rider". That is something I realise more and more with every one of your vids I watch.

"kawasaki never made shock adjustments easy"
**me with my 2011 ER6f with the side mounted shock and adjustor in clear sight**: hmmmm

All joke aside, another brilliant video

As always great info, thanks!

I also ride Bridgestone S22 since a month now, but i noticed that the tire pressure at maximum load increased to 42psi for the front tire. All my previous front tires where rated at 36psi as a standard from the manufacture, but now it has gone up 6 psi. Is something changed in the Bridgestone front tire technology? Since the rear tire remains the same as always (42psi)

whos here for the 235 pounds setup :D?? me first! 99.9k subscribers! loged! legend the advice for tyre pressure regarding the debris! what haeppens when the tyre pressure is too high?

What tire pressure do you suggest, 125 lbs, r1m with the rs10 tires, preload is as soft as possible in rear, and like two turns in on front. No other adjustment on suspension (road 1 semi active)

so I went and checked my old fazer 600..oh dear, no chance..is there nothing worse than budget suspension?

love this channel mate. I'm a member on your site. would love to see a suspension tune on a late z650 please

the guru

You should give online education mehchanics all over the world

I'm not even sure what I'm doing here. I have a fairly new KTM Duke 125, which I can barely ride and I was just wandering if I should touch the default preload setting on the shock (the only setting there is), because I'm lighter than average, I think. So I was looking around the internet, stumbled across Dave’s videos here and on the OTT channel and watched dozens already including some GSX-R750 disassembly. It’s fascinating :). I'm definitely going to recommend the MT-07 fork fix video to my colleague, who has one. Great stuff.

Yeah I bought a spammer wrench for my z900. Waste of money and it scratched my frame. Should have just used lube, a screw driver and a mallet in the first place.

Ah ha! Another on point video. Looking forward to watching the full video with my morning coffee tomorrow. 🙏🏻🏴󠁧󠁢󠁳󠁣󠁴󠁿

We need 20 Daves all over the country.. And 20 in each developed country.

Dude should have 1 mil subs, everybody not subing doing this man an injustice

This guy is the best thing on the planet I've learned so much, total respect 🇬🇧

It’s a shame manufacturers don’t offer an interactive setup page so we can all get the most out of these incredible machines.
Until then, we have talent like Dave, but he is just one man

Dave I've noticed face masks .wheres yours chap you need to protect yourself. Keep safe!