How to install a wall mount and charger for your dyson hand held vacuum

Great video although I wish someone would discuss how to find a stud in a wall and even making initial hole and what anchors even are 😔

Should I use a longer screw or shorter

Thanks for the gr8 detailed video Tom. Do you need to screw into studs or is the drywall sufficient? It appears like the drywall will hold since you didn't mention anything about finding the studs. Since it is just drywall, can you use a hand held screw driver or do you need a drill? That is a good idea to mount it in the laundry room with just the base. The Dyson video show the mount with the entire leg attached to the mount on the wall. That is nice bcuz everything is all together, however, it takes up more space and it's not as easy to mount it next to an outlet in a more confined space like next to a washer or dryer. You could fit the charging base next to an outlet better with only having the base mounted and I guess just store the leg somewhere else.

Sorry to point this out but you have installed it the wrong way around. The cups at the end go on top to store attachments.

Thank you for the video. What screws do you recommend to use?

All these videos skip the actual drilling and anchor parts and that’s what people need to see

Thank you!

Great video, followed your instructions, went perfectly. Thank you!!

Thank you! :)

Many thanks for the video. I way scratching my head. From Cyprus

Looking for some advice:

With a wireless vacuum, would you install the mount high enough for the vacuum to be resting solely on the mount, or would it be best to have the base of the vacuum resting on the floor to take some of the weight off the mount? My bf just installed our mount but it's high up enough the vacuum isn't touching the ground and all its weight relies on the mount. I am pretty nervous about it falling because I have a cat. I have been watching countless videos and searching Google but haven't found an answer yet. Is there anyone who could give some advice, or suggest an additional way to secure it as I'm not sure if this mount required double sided tape and if so—I would assume it can't be re-mounted with out it...

Yep, I had it upside down. Makes a lot more sense now 😂

Awesome - cheers mate!

Thank you very much

I wish this showed the anchor installation ☹️

Can I set up this dock on a wood closet? Do I still need anchors for it?

Where did you buy your wall anchor (red) from? I need this for some of the other components. Great video!

you are a gem. thank you.

THANK YOU! You explained how to do the install clearly and without a lot of personal banter... some people get caught up in hearing themselves talk rather than cutting to the chase and helping us non-handy people out! BIG THUMBS UP!

Thanks!!!
I haven’t bought one yet but I’m planning to. I just don’t know where I’m going to put it. How much space does it need to be away from the wall? I’m thinking I could potentially put it behind a door… But I may not have enough space. I’d sure like to know how much space is needed for the Dyson docking station

Everyone said Dyson wall mount and showed how it pierced the wall. You explained in detail how to place the charging cable and charging port 🤩 Thank you very much, exactly the video I was looking for👏.

Easy to fit the plug, nightmare to get it back out!

Mine was nice and secure for months until it got very lose I used bigger plugs and still no good.... please help 😬

Do you need to put in studs only?

Thanks so much for the detailed video of putting the plug in the dock. I liked how you hung the long bit to the size to use the wall space you have super clear and simple super duper 🥳

Thank you so much!!!

Lol if it wasn’t for your video I would have never did this. I didn’t know you needed to push the charger so hard up the little nozzle tube for your charger. Thank you

Were screws/rawlplugs included for you guys? I couldn't find them.

Thanks Tom, great video.. My V-8 came with studs (as you used) and screws. Is it really necessary to use the studs if I am screwing into a stud? Thanks in advance.

Thank you! There is no way I would have figured that out from the instructions. This video was what I needed!

What a legend

So helpful since an otherwise useful product fails to explain clearly what you managed to demonstrate. Cheers!

The best video on how to install a wall mount for Dyson. I gave him 100 out of 100.

Dyson !! If i knew i have to screw by myself station to the wall i will buy other model of vacuum!! Big NO ! And no parts inside as well to do this !

Omgosh thank you so much! I totally was going to screw it on the wall and have the cord hang from the side haha

Lost the screws in my move and I don't want to take the mount to the hardware store. What size screws did you use? All my inventory screws are too fat.

Thank you! the instructions were really hard to follow!

That must be the cheapest stand very little money can . What a fail

So— am I the only one who is concerned about it reaching full battery but it’s still plugged in?! I was about to mount the wall hanger—but of course this thought came to mind. I just prefer that I disconnect the charger from the vacuum once it’s reached full charge. I’m guessing I can just pop out the charger head once I see it’s reached full battery? Anyone do this? Or ???

Well done, brilliant video, thanks

Yeah the actual drilling of the holes and what to use and what is an anchor, etc...is what is needed

You skipped the most important part about installing it on the wall. What size bit did you use for the supplied wall anchors?

Does it have to be in the stud ?

I have a v8 model with no screws or anchors. Do you know what size to use? Thanks.

Thank you from France 👌🏽

Mine was screws missing. Called Dyson but sent me much smaller screws. Did you buy screws sperately?

Thank you for the great instructions!!