RC Robot Car - RC Controls and Arduino

Is this Remote control still good or there's something more advance nowadays? Thanks.

what a waste of money and effort. I programmed the Transmitter via my computer to do the same.

Can I use sbus instead of Ibus in code, for my R8EF reciever has sbus instead ? I Installed the sbus library and included it in code, and deleted the ibus library. Changed all the ibus notations to sbus but when I go to compile I get a message no such file or directory.

Hello Bill, Maybe one day you can do a video about just a few of the vast number of FlySky Receivers that are available. Also, Improvement modifications such as replacing antennas on the Transmitter for improved performance.

Great video! Thank you very much.

Hello, Fantastic video for introduction to arduino RC. Can you please make the option available for you video to be saved to a playlist. Right now only sharing is allowed.

I ALWAYS enjoy watching your very well presented videos! Very detailed, made easy to follow, and comprehensive. Thank you for the hard work you definitely put into them!

GOOD 👍

Can i use a esp32 for this?

I have a doubt, can the same application be used for ships ?

can you different radio? like austar?

I just bought a radio controller for my son, this video is well introduced and helps us a lot. Thank you!

Hi, Once i load channel map sketch, i am unable to load motor programe i prgraame run in loop and i am unable to use serail port to load prgrame..please help

Hi
Can ESP32 decode SBUS from a RC receiver to control servos and stepper motors etc. would be great to see a video on that.

I have two 300W wheelchair motors running a heavy cart that spools up a hot air balloon fabric (using a winch motor). I am using a cheap 48V-60V 1000W Motor Brush Controller. I want to use a Sabertooth 2x32 with radio control. That part is simple enough, but then I want to hand it off to an Arduino for a parking routine (following a wall and stopping in its space).
How can I hand off the R/C to the Arduino and wire it to work?

Hi
If L298 is used instead of TB6612, how should the circuit diagram be?

Selam
tb6612 yerine L298 kullanılsa devre şeması nasıl olmalıdır?

When flysky with Arduino I want to in increase degree servo rotation Example before servo rotation only 90 to 180 degree . how to do can help me dear.

Need some advice. There is a way to connect the transmitter to the analog in in a Mega?

Thanks!

Most informative video ever, for those stuck with an UNO instead of a MEGA like me, do connect the ibus pin to the RX0 serial port in your UNO. 👍

I wish you did this but with a drone, having the Arduino as a flight controller

I'm a beginner with ardunio. I appreciate your content and have learned a lot. I want to control a linear actuator with the 3 position switch on the FlySky i6x. I wasn't able to find anything on your channel or anywhere else. Can you point me in the right direction?

Thanks you my teacher. ❤❤❤

I remote controlled a 10 hp Craftsman steerable track drive snow blower using an Arduino and all 10 channels on a Flysky RC controller. I wired and programmed the receiver the same way you do in the beginning and didn't use the I-Bus method. It took me a while being a novice with Arduino but got it all working. 8 servos ( 4 12 volt 180 kg and 4 6.7 volt 20 kg ) 1 12 volt geared motor along with 2 linear actuators. I can remotely start, control the choke, primer and throttle. I can engage and disengage the auger and the drive system. Shift into any forward or reverse gear as well as steer, lift-lower and rotate the chute. I added the linear actuators to lift the front when reversing or transport mode.

is there a similar library for SBUS

can I use brush and brushless motors without ESC with the FLYSKY receiver ?

So I can't use ibus with my arduino uno?

Hey, great video. I appreciate how you distill things down to convey real understanding. Re: Arduino between RC rx and motor driver: I've been told that there is a passthrough mode on some Arduino PWM ports where incoming PWM signals can simply be passed through to the motor driver or the port can be set to disregard incoming PWM signals and that puts the Arduino in full control. It seems like you are using a different, more intuitive method where you measure the PWM input and then output (or not) PWM on a different port, no? I've been told that this method introduces significant latency. Could you speak to that? I'm about to start on this exact thing here tonight. Btw, if I'm only using 3 channels (motor, steering, Arduino control ON/OFF) ... can't I use an Arduino Nano for this project? THANK YOU for your help. :)

this is an amazing channel thank you sir!

How to control 350watts DC motor in same method?

Excellent vid. I thank you with my sub. Subbed.

im stumped, every ch has values of 9980 and 1038, how did you get 0 and 100? i used code that your using with ibus

You can use the serial mode on an Arduino Uno if you're willing to disconnect the receiver from the Arduino's TX/RX every time you want to program it.

I don’t usually comment on videos but this is amazing. First channel on this kind of stuff that has left me feeling empowered and capable instead of confused and discouraged. Thank you for your amazing videos and keep up the great work.

is there a video on how to do it without the IBUS and with the L298N?

Thank you very much for this excellent and short explanation
شكرا جزيلاً

Thank you so much for putting the input values for each channel!

Great Video Top!👍

Hi Bill, How can I do I-bus communication with Raspberry Pico?

So much information! I'm learning things I need for unrelated projects. Thanks man!

Line 120 of sketch ;'serial1' was not declared in this scope . Please Help!!!!

And please tell me at what time you are free

Play speed1.25x

Thank you for the amazing tutorial. Would this project also work using a raspberry pi 3? Thank you.

Awesome video! Would love to collaborate with your channel Bill :)

can you give any information about distance?

Can I use a 4 channel rc and receiver ?

Hello Bill, what a great tutorial. Inspiring us. Thanks for all the good videos. Just got the rc controller to replicate what you taught us. Thanks again

Thanks for your effort.
I was wondering how could I use my old RC car, it had its factory reseiver broken a couple of years ago, now I know what to do. Please, keep creating videos for us!