Ubiquiti Loco M5 Setup

Does the CAT cable coming from my ISP service modem supposed to be plugged into my LAN/WPS jack or Ethernet jack from my modem?

This video was so excellent. Needed to deploy these bridges in a couple hours and watched this video at 5am. Perfect and thank you!

Thanks for the video. Can the source for "station" unit be any in AP in my network? I have a outdoor AP which has a pretty good signal to shed. I want to have an ethernet connection with router>switch in the shed. If i buy only one nanostation unit and configure it as "Station" would this work?

You did an absolutely fantastic video. Subscribed. Thanks.

How can I make it supply Internet wireless without putting a router

Hi, once we already point to B area. how strong is the internet signal at B area? 500 meter can?

great video thanks awesome video. very easy to follow. cheers

شكرا لك من اليمن🇾🇪.

Just a note that it should’ve been Megabits

I'm a bit confused on one part of your diagram (on the piece of paper). On the B side the yellow wire from the Loco going into the POE port of the injector (hence it's getting the power). You have listed on your diagram a CAMERA POE with the blue wire. You have already used up the POE on the injector. I don't see how the POE Camera is getting power in this situation by plugging it into the LAN port? I assume you'll need second POE injector and you would plug another cable from LAN to LAN on both injectors and the POE Camera to the POE port?

Thank you for getting to the point and not rambling, best video I have watched in some time!

Great video, thank you!
I am setting up the B side, but no SSID is showing up for my A side when I press "scan" even though the popup shows 3 other networks. I have my A side ca le connected to POE, not LAN, and B to POE and my computer.

Very helpful video. Saved a lot of time and effort on my end.

Very helpful video. Saved a lot of time and effort on my end.

Hello I have a pair of loco m5 wireless bridge from my house to the shop, ever time I loose power I have to factory reset and reset up the parameters to get online again. Is there a better solution?

After the full set up can u get wifi network or u will need another router?

So awesome…u rock

✍

Good explainations UberGeeks....

Regarding the IP source in your video, can that connection (LAN port) be sourced from a router connection?

Am going to ask a really basic question. When one sets up an M5 as an AP or access point, can other laptops connect to it as well, or is this JUST for the connection to another M5 (station)? tx

Excellent video. Clear. Covers everything one needs to know. And we can HEAR you. So many try to do helpful videos but they do not tend to their voice and often we cannot hear what is being said. Your voice volume is GREAT.

Прекрасное видео. Great tutorial. Thanks a million!

Are you able to transmit a WiFi signal with just one of these?

U R GREAT

Simon, All is working will with my M5 setup. Thank you.
I do have a question. I have house "B" connected to a switch. The switch is connected to a WiFi extender that is setup as an access point. My computer is connected by an ethernet cable to the switch.
I want to access my computer remotely from another location. I will need to set up port forwarding to the router. I will need port 50001 and port 50002. Will having the M5 between the router and the computer be an issue?
I also need to set the IP Address of my Server to static so it will not change if the computer is restarted. Will this be an issue?

Do you have any recommendations for any free DNS service?

I know I am asking a lot of you but, you helped me set up the M5's so easy and you are light years smarter than I.

I've spent many hours studing ip address setup, I wish I'd seen this 1st. It skips straight to what I need in a logical direction.

Thank you for the detailed instructions. Everything worked immediately during the first installation.

these are best instructions for setting up the Nanostation Loco M5. it was very detailed, easily explained and understood and . Thank you very much.

Nice detailed explanation, that is very excellent, thank you so much for this great video

The illustrations helped so so much

Thanks!

Can you setup the “building A” as AP Repeater instead of access point? I have wifi on my back porch, just need to shoot it over to my shop. This would eliminate the need for isp running a cable to my back porch into the nano. Im only shooting to shop about 50 yards away.

Nice explanation

Can this one go up to 25km

This presentation made every step clear to understand and the explanation tied everything together at the end. Thank you

I followed your video on setting up locoM5. No luck. Now I can’t even log back into the locoM5. Tried factory reset with no luck. Do you have any suggestions? I was using a Mac.

If I replace the station b with a new one, (old one got wet) do I need to reconfigure from the start? Or will I be able to log into the station program and select the acces point name? It was set up by another party. Thanks!

So using the the A will only function as a router

Hi, I followed the set-up and still don't have internet on pc via Ethernet at point B

Excellent presentation of the setup process. Easy to understand. Well done!

How can i see a password with lan cable in a router box

I’m trying to setup a connection to get internet from a house 900’ away from second home. Not a clear line of site (brush no building) I bought a rocket prism r2ac and waiting on the antenna and the nano station m2 get here. Is this an over kill and I should just order another nano station? I’m old and technically challenged. Thanks for any advice.

Is there any magic needed if adding another set of these units to extend the bridge to another building...so two AP and two Stations linked together on the same network

I was told I needed a new nano and I’m having issues setting up the new with the old. Any advice?

Nice job.

Price

Very very clear and helpful 
Thank you very much!