Комментарии:
Circuit diagram and map???
Ответитьtransformerless, but dangerous. So use caution
Ответитьcan we measure the output voltage of transformarless powersupply wihout connected to the load?
ОтветитьI don't get why you use P-P instead of RMS.
Ответитьmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm (230x1.4142)=325.266 -6 = 319.266 ya think a decimal point , can mean a lot triple check
ОтветитьCan you please send me the pcb board link
ОтветитьSir gi your explain is very Quite Amazing
ОтветитьAll led drivers can have transformerless power supply, but why we don't.
ОтветитьThank you for a very good explanation
ОтветитьSend pcb pakistan?
ОтветитьSend pcb pakistan?
ОтветитьGreat! Good explanation about how to select the polyester capacitor based on the required output voltage. Thanks for sharing.
ОтветитьDo you have circuit in PDF or JPEG format? I want to make pcb at home instead of ordering on online store. In my country, it's expensive.
ОтветитьWhat's the output current
ОтветитьI want pcb board with components another one 12v pcb board with component.
ОтветитьPlease, how much value for bleeder resistance
ОтветитьIt is not working
ОтветитьUr schematic n ur pcb is diffrent
In schematic u have not shown the value of blender resistor
No discussion on zener diode 1/4 or 1watt????
For 150volt dc pls let me know the value of component
ОтветитьHi, can you please tell me what the R3 does, couldn't you connect it directly to the full bridge rectifier and ignore adding it? If you or someone else can shed some light on my question I would be forever grateful.
ОтветитьThese capacitor output is not safe, if the input voltage raises to a high voltage, the capacitor might blast. This happened to me twice.
ОтветитьCan i use capacitor of 2.2 micro farad instead of 1.4 micro farad?
ОтветитьHow if i need 24 volt dc?.. could you give the values of all the component?
ОтветитьPlease show the calculation for choosing the correct capacitance and voltage value of the filter capacitor .
ОтветитьConsumers friendly technological designing are always different from business friendly. So many extra components and complicated designing are good for business.
ОтветитьHi, A good effort of details in your video. It does not show the AC voltage before the bridge and DC voltage after the bridge prior to filter.
ОтветитьSir from where you got the printed pcb , I need some pcb
Ответитьthanks.but i test many times but never cant do this.i use 1 m ohms and 750 nf.i dont want a specefic voltage ,i just want to test but never succeed.i make circuit on bridboard bread board. 😭😭😭😭
ОтветитьSir plz help transformer less 12v supply my filter capacitor is heatup what reason
Ответитьwhy not use a thyristor - - gives much more output power
ОтветитьThe instructor does not know what he is taking about. Some of the comments below have also noted his incorrect description of the way the input capacitor works. The input capacitor does not have any dealings with the voltage on the output. It only controls the current. And the way to remember the current that the capacitor will delver is this: for each 100n in a full-wave circuit, the capacitor will pass 7mA. The capacitor he has used is 155 which is fifteen lots of 100n so it will pass 15 x 7 = 105mA.
It is now up to the zener diode to create a 5v1 voltage on the output of the power supply. The capacitor has nothing to do with this voltage. Now we have a problem. If nothing is connected to the output, the zener diode will drop 5v1 and the current through it will be 105mA This is 535mW You need a 500mW zener.
Now, the next thing that happens is this. When you connect a motor to the output, the motor "robs" (takes) current from the zener. You can take up to 90mA and the output will be 5.1v You can go as high as 105mA and the output will be 5.1v But as soon as you take more than 105mA the output voltage will drop and as you take more and more current the output voltage will drop more and more and more.
Want to try making it
ОтветитьEski life kitni hogi agar ese regular supply (24x7 h) ke liye use kare
ОтветитьI made it.Awesome Project.Whats the difference between tramsfomerless and transformer powersupply?
ОтветитьCan we use this for esp32?
Ответитьcould you please make a video same for 24dc 10 amps to 12v dc 5amps
ОтветитьGood. But the circuit is shock hazard at dc point which is very dengerus..
ОтветитьHello..can you pls tell me if I want 12v at point A, with 300 mAmp, what should be the capacitance , I calculated however I m not sure...it is coming like 0.00000292712626451....can you help here
Ответитьsuper bro thank you very much
ОтветитьWhy is the output voltage more..... 5.45V when a 5.1V zener diode is used
ОтветитьPls give me the gerber file
ОтветитьCan I use only a resistor to imitate the value of the Impedance? like a resistor with impedance 3192.6?
ОтветитьCan you pls snd gerber file and circuit diagram
ОтветитьDiagram ya PCB layout chahiye
ОтветитьHow many ampere at 5v sir thank's.
Ответитьhow can i get 1 amp output current cz i wanna glow 40 rgb leds connected in a parallel
ОтветитьSir please share your contact.
ОтветитьHow to determine the resistor which is connected parallel with this 1uF capacitor??
Ответить