Programming Generic STM32 board via Arduino IDE and ST-Link V2

I'm using ST Link V2 Programmer to program NRF51822 module. I did the normal code in Arduino IDE. I'm getting this error.

debug_level: 2
0x4000
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
adapter speed: 1000 kHz
Info : Unable to match requested speed 1000 kHz, using 950 kHz
Info : Unable to match requested speed 1000 kHz, using 950 kHz
Info : clock speed 950 kHz
Info : STLINK v2 JTAG v29 API v2 SWIM v7 VID 0x0483 PID 0x3748
Info : using stlink api v2
Info : Target voltage: 3.285390
Info : nrf51.cpu: hardware has 4 breakpoints, 2 watchpoints
nrf51.cpu: target state: halted
target halted due to debug-request, current mode: Thread
xPSR: 0xc1000000 pc: 0x00012b98 msp: 0x20001c48
** Programming Started **
auto erase enabled
Info : nRF51822-QFAA(build code: CA/C0) 256kB Flash
Error: Cannot erase protected sector at 0x0
Error: failed erasing sectors 0 to 1
embedded:startup.tcl:454: Error: ** Programming Failed **
in procedure 'program'
in procedure 'program_error' called at file "embedded:startup.tcl", line 510
at file "embedded:startup.tcl", line 454
Failed programming: uploading error: exit status 1

Please please help me with this. Thank you.

Thank you for your knowledge. I made this, but the only issue I have is the pulse and the motor are not synced in time. I rotate the wheel after some seconds the motor moves. What could be the issue? I am using DM556 driver with nema 23

Can stlink upload sketch without programmed arduino bootloader?

St link port com not detected?

Is it possible using arduino nano expansion module with this stm module ?

I also make stm32 videos. Subscribe to my channel :)

Hello. Do you know if arduino compatible TFT libraries work with this STM32F103? Adafruit library for example.

Can you read the serial values via the st link?

Worked, than you!

Sir, thanks a lot!

can i use stm8 board and arduino ide with St link programmer

hello sir

fuck yeah dude thanks alot

Great video , DId you ever try using the boot-loader Roger talked about ,so you can use on-board serial port for programming and communications ?
wondering how much a pain it is . Im thinking of moving some ideas over to STM and would like to work withe devices (blue pill) as if they were a super Nano . LOL

I managed to blink the LED but when I try serial communication (with my ftdi RX/TX connected to A9/A10) it does not work. Do you have any ideas of how I can solve this?

Let me ask you a question. I notice that plate has a Cortex M4. So does it have dual core? Can you achieve multiprocessing with arduino for multitask?

Thank you for sharing your work! I'm also looking for Linux examples. One question: How do you think the STM32 architecture compares to Arduino? What do you see as the advantages/disadvantages, I mean...

there is no port with STlink to choose

Hey man, do you need to change boot status to program via STLink?

can I reset chip printer by this ?

Nice!

Use OpenOcd to drive the stlink on Linux. You can also make use of the Eclipse IDE.

arm-none-eabi-g++: error: C:\Users\admin\AppData\Local\Temp\build3991986179643547692.tmp/core.a: No such file or directory

Great tutorial man, thanx.
Do these STM32 drivers & apps work on Linux?

can we also program stm8 mcu with arduino?? STM8S003F3P6

Thanks so much, very good explanation, I have question about STNRG and STULX is there is some videos can help me to get start using STNRG and STULX.

yes but u lose USB Serial functionality with Generic, anyone knows how to get it back?

can you send the connection diagram between stm32 and st-link . my email [email protected]