Restoring a Classic Land Rover

حاجی برای یه کلاج که همه ماشینو اوراق کردی !!!

Looks like the car called the anti christ from gods must be crazy

Love this, always great to see old icons being restored! 👌😊

Green with envy. What an absolute beaut!

Took 4 years but eorth every minute

Fantastic filming

That rig is so clean, restoration looks easy

Don't know why anyone would put a soft top on a Land Rover with a good hard top.

Mate that flywheel is scrap

what was the problem with the clutch the drive plate looks like new.

im about to watch this, new clutch, remove the roof? ok lol

Good to have car mechanic knowledge and a willingness to help.😊

Loving this project…. Belts and braces Land Rover 🍺💥🔨👍🎉

Eu amo assistir esse canal ❤ ele fala de tudo que eu mais gosto @carlrogers

Hi I had a series 2 90 inch with a clutch gone after I removed the gear box which was horrific I realized it was easier to remove the engine to replace a clutch not that helps you now

this is not a restoration, but a conversion, alas, the car was good!

Does the new soft roof offer any measure of "roll" protection?

diesle, groovy trip!

Nice video,though rather at a loss to understand how replacing the clutch and fitting a soft top is a restoration !

replacing the cowling between the floorboard and firewall?

Ось на решті побачив, що ви у Франції перебудовуєте віллу)

Sounds like it needs a tuneup. 🤔

Only just come across this but enjoyed watching it. Just a tip for removing the bronze 1st motion shaft bush from the end of the crankshaft. Pack the space inside the bush completely with grease and then find a bar that just fits the inner bush diameter. Hammer the bar onto the grease and the hydraulic pressure created will get under the end of the bush and force it out.

It's so great that your boyfriend could help you!

what do you pay for a project car like this?

Nice job like the roof swop...if you don't mind me asking what did you pay for the landy in the 1st place?

That’s definitely not the original number plate for that vehicle. It’s a early 80’s vehicle on the a 70’s chassis plate

Erm, you didn’t have to do all that.
I removed gearbox and transfer case for overhaul and renewed clutch by just unbolting and lifting the seatbox up, just enough to allow the shifter boxes to clear it, and drop it down. No need to remove half of the car.

Stop riding the clutch

So glad that we're preserving these beauties . They were built with a lot of love and passion !

Ah it's about 3 hours work.. 3 days and many cuts later..😂 never stop taking on those ambitions jobs 👏

You can add some music to the video... The thuds and noises make it a little hard to watch till the end

대한민국의 서울에 사는 할머니가
그대를 ~ ^^ ♡ 항상 응원합니다

I want one Mum 😁

Great Work Guys, and the vehicle what a classic it s so british , I love it

Thanks for leaving in all the mechanical sounds during the high speed segments in your vid's. Well done!

Riveting content indeed. Well done.

Can I buy the hardtop off you? 🥹

Or just put it on a lift.

What's the point in having a land rover if you're not going to take it off road.

should have replaced the throwout bearing while it was in bits - but good job nonetheless

Great video, thanks very much. What model is this 1970 Land Rover? Is it a Series 2A?
Thanks in advance.

skiLL Landy project mad restoration Langka buAt i mage terniLai tamPa baTas mad mad mad madskill

Car looked pretty good

👍👏👏👏

what are the lil doors beneath the windshield on both sides

No new flywheel. :(

Does this ever bring back memories, if doing this job on a series 1, but we had no such sofisticated tools in my day, was all hand tools and man power

First look on chassis, always a disaster_ forget Diesel engine pure shit- 😢- otherwise part are not expensive in England, but custom charge are high. Look always derelict 🥰