Blood Oxygen & Heart Rate Measurement with MAX30100/02 Pulse Oximeter & Arduino

hello with the node mcu it is possible

I WANT TO USE PULSE OXIMETER FOR NON INVASIVE BLOOD GROUP DETECTION, HELP PLS

Your work is very much interesting. I have tried to use MAX30100 with nodeMCU. Sensor is providing result while NodeMCU is connected with Oled also. But while i am trying to take the data to thingspeak or blynk app then MAX30100 showing zero data. MAX30100 not working then, not sensing beat. I am fighting to find out the solution. Will you please sir/any one help me to solve it. I will be grateful.

whats the name of android app?????

when I try to compile the code for the last method. It shows
Low memory available, stability problems may occur.
and the code cannot be uploaded.
I have already used the Flash command
still iam facing the issue.
what do I do

for(;;); doesnt look right ;)

I have a exam i need your answer yhis code i can use it for max30102 answer me plz

The BPM is very much fluctuating

Whether we can measure oxygen level in foot?

Where to learn Arduino coding and esp32 coding....

Does it work for MAX30102 ????

Sir which software u have used for simulation??

Why we need connect INT pin to D0?can it''s work without connect INT pin to D0 ?

Sir can we pls know which language have u used for coding

boss letak kat nadi sikit

Just what I have been looking for. Thanks for the video and resources.

Amazing stuff. The electronic voice though is naff and annoying. Why not use your own?

In which software they have drawn the circuit

How to CONNECT MIT with THE BLITETOOTH???

how i will use this code for arduino uno.there is an error when i was compiling the code in arduibo uno.

Hi, how to code the bluetooth?

Hello. Can you please help with how to configure this to work with max30102? Ive been trying and its definitely not working for it. Thanks in advance.

It throws an error in the CircularBuffer.tpp file. The code you gave gives an error to compile for arduinu uno.

Please share working code, time is wasted.

Plzz tell about a what components nd quantities using this project...

Bro it is showing some code error of some function not returning parameters so no response error what should i do

good way of explanation

very nyc vedio can you help will whole code you uploaded in this project..

sory sir. I have question. I have MAX30100. when run on arduino led it doesn't work. but when using esp8266, the sensor works.

May I ask waht components should I used in alternative of finger when I need to prove it in proteus simulation?

Hi I want to do the same project in my mini project can u pls help me in making the project

Could you please tell which connection wires we could use

I have a problem, I use the MAX30100, when upload the code to Arduino is OK but in the serial monitor doesn't show anything, the only shows the serial monitor is "initializing pulse oximeter..." and that's all

Hi big fan! Is there anyway you can make using m5stack please?? I really need you’re help! I can donate to you’re cause sir!

is this code work without blutooth module

Initialising pulse oximeter failed
I have done all the connections properly.
Any fix??

I'm using M5stack version of max30100 and serial monitor shows first 6 characters of the first serial print message (Initial) only, when I disconnect the module then the Initializing message is completely shown and of course since the module is disconnected after a few seconds it shows as Failed.
Any idea why this is the case with my build?

I'm getting "error compiling for board Arduino Nano" how should I solve this

Hi, thank you for the video. I'm with a problem, when I try to use the max30100 without any pull-up resistor in 5V it doesn't turn on, and when it is running I can't put my finger too much near the RED led, as much as I approach my finger less the sensor read oximeter and cardiac parameters.

Thanks

Hello, can i buy your max30102 sensor. Because, my sensor is not work

Hello sir thank you for the video
But I am facing a issue I want to increase its penetration current can you guide me how to increase or decrease its penetration current

Since i2c port is used. Don t we need to mention address of i2c device

Anyone here know which program I can use for simulation of this circuit?
Cause I've not found MAX30100 on proteus

I2C error from my side

Can we use this sensor in smart Helmet ?

may i know, what is the language used for the coding?

Thank you so much, it is really helpful!

Hey, why the bluetooth module?

is this compatible in MAX30102?

I have error compiling why?
I fixed the low memory problem then I have this