Комментарии:
Is it possible to drive an ignition coil with 12 Volts supply?
ОтветитьGreat video
ОтветитьI am planning to use this as a driver to an ignition coil. I burned one unit already. I think the mosfet inside cannot take the backEMF. I will try to put a snubber diode accross my primary to combat this, but I think I might have to get a beefier mosfet and the ZK-PP1 which does not have an internal mosfet.
ОтветитьIs it possible to drive a tesla coil with it?
ОтветитьGreat first class demo, thank you.
ОтветитьSolid test
ОтветитьEy my friend, great video. I was looking for a thing to create a cleaner inyector, someone recomended me the pwm generator of 1 way (the little brother of zk-pp2k) but looking at your video I will need the pulse generator or thats what I understand.
With this I can config the inyector to open every 0.3s to make a fast tick tick tick for the cleaning process, correct? I was trying to know if I can connect 4 inyector at once on this device or maybe better one per one?
I connected this unit to 16vdc. All controls work as specified. BUT… the output remains at 16vdc at all times! It does not turn on or off with the “out” control. No square wave is shown on my oscilloscope. I thought that the unit was bad, but a second unit does exactly the same thing. Any idea what’s wrong? Any help would be greatly appreciated. Steve
ОтветитьGood demonstration. Thank you.
ОтветитьThank you
ОтветитьThis is the best video I have found to explain these devices, Thank you. I was wondering, is this for brushless motors only or can you use brushed motors as well? Also, what is the recommended input voltage for this device? I know you said between 4v-30v, but would a higher voltage have any benefits? Thank you RJ :D
ОтветитьHi, please can you describe how to attach a heatsink to the mosfet? Can i fix one on top or is it necessary to remove the mosfet? Thank you!
ОтветитьHello, what is the ouptut frequency in pulse mod ,please?
ОтветитьThanks...Great explanation on how this works. Keep up the good work!
ОтветитьMindboggling post, very interesting. Keep posting.
ОтветитьI want to control a single LED of 1.8V. Is it possible to lower the output voltage? Maybe with a buck converter behind the PWM?
ОтветитьHola Ahmad, soy de Argentina. Te pediría que subas un video como éste del ZK-PP4K es un módulo bastante reciente. Le mando un saludo desde lejos.
ОтветитьThanks for the tutorial video. Can I get your contact email?
ОтветитьGood review
Thanks
Thank you for nice video!
ОтветитьGood day @Robojax, I´m new to your channel, and this video lead me to it, i found your explanation very easy to understand and i thank you for uploading this video, i have just 1 question, the output signal´s duty is control by this driver, Im trying to control a laser for my cnc, it has 3 pins 12v+, 12v- and PMW, do you know if i can use this output for the pwm in the laser? if you made a video about that please point me in the right direction. Thanks you so much!
ОтветитьGostei muito da explicação 👏👏👏👏
ОтветитьThanks
ОтветитьHi great video as always. You mentioned a a heat sink on top of the mosfet any idea what to use
ОтветитьDoes it save settings after power off
ОтветитьThank You Sir I want to know with Battery( rejuvenating )
ОтветитьThank you sir ❤️❤️❤️ nice video ☺️
ОтветитьIt would be great if you could do a followup on elaborating what the frequency actually does since you have the duty cycle which defines the on off portion of a cycle.
ОтветитьSir I think you are slow in uploading the video of arduino lession plz make it fast 😤😁😁😁
Ответить