Комментарии:
Hello my Friend 👋👋👋
ОтветитьThank you
ОтветитьParkside has awful quality...
ОтветитьОтличен, както винаги. Но не разбрах защо използваш паста, вместо тинол. Някои са откровени lead-free боклуци, които и на 240 градуса стоят като зле калайдисана тенджера. Преди много време имах случай в който пастата попадна под корпуса на чипа и накрая имах чудесно окъсена платка :) от тогава не ползвам :)
ОтветитьParkside should pay for this troubleshooting xD Heard that many 8ah batteries have that problem(personaly never had). No bluetooth module that could be compatible to replace?
ОтветитьMais um excelente trabalho, parabéns, obrigado
ОтветитьThis video is missing an explanation of how you determined that the bluetooth module is the culprit.
ОтветитьWow. Awesome lab
ОтветитьExcellent troubleshooting! Could you try replacing the 7533-1 with a Nisshinbo NJW4184U3-33B-TE2? It's SOT-89-3, 35V and 300mA. Current spec is a little low, but it was the best I could find
ОтветитьVery nice clip. I have the same problem with the button, but the battery works, but I can't see the charging status on the LEDs. Is it the same problem?
Ответить👍👍👍
ОтветитьÖnce güvenlik. Güvenliğiniz için önce pil bağlantısını kesin. Daha çok video içerik üreteceksiniz başınıza birşey gelsin istemem
ОтветитьAwesome troubleshooting as always. Many parkside users have issues with smart batteries and now you found solution. Anyway 99.9% of users don't use BT on their tools, it is just making problems. Great work as always my Friend 👏 👏 👏
ОтветитьHave you lowered the bluetooth module and changed the voltage regulator? Great work my friend
ОтветитьShould i remove the bluetooth module to avoid this problem
ОтветитьFaulty BT module 🤯
How is this even possible?
Nice troubleshooting Brother ✌️
nice
ОтветитьWe need a fix for usb c adapter
ОтветитьI have almost tha same problem , except main is charging and tool work.
ОтветитьHi! I removed the BT module and replaced the resistor and regulator. The battery now shows the LEDs when you press the button, but it doesn't charge. LEDs show that it's full, and the chargers green light stays on. When connecting it to a tool it works for 2 seconds and then cuts out, like you had in de first part of this video.
Any idea what I could try more? I've added a 20 Ohm resistor in the same method as the French video did it.
Can you make a Video how to Install a Display and USB Ports to the 12Ah smart charger? Very nice 👌
ОтветитьThe problem is not solved, the BT module is missing.
ОтветитьParkside ürünüm yok yinede izledim :) Ercan seyrettiriyorsun videoyu :)
ОтветитьGood job man!
May I know which thermal camera do you use?
Your hot air gun is either not adjusted to the appropriate temperature or cannot provide the desired temperature. Because during the disassembly process of SMD components, you do the disassembly process before the solder melts completely. This may cause the solder pads on your electronic board to break.
ОтветитьNew to this but why does it have a BT module anyway ? 🤔
ОтветитьWhy is there a BT module in the battery?
ОтветитьWhen you solder that resistor like you did it by pushing it down, it will stress the other solder point of the resistor/circuit board. You should have been using hot air or only put solder on one of the solder points and then the other after the resistor was installed.
ОтветитьHi , i liked the magnifying tool , i have bad sight . Can you share the idea behind it .ty
Ответитьercan hocam merhaba. kanalınızı ilgiyle takip ediyorum. bir sorum olacaktı. benim matkabın BMS kartında RS1M diyotu yandı. kartta sorun yok. bu diyot yerine kolay bulabileceğim muadil bir diyot önerebilir misiniz? US1M uygun mudur acaba?
Ответить3 yıl garantisi var, aynı sorunu bende yaşadım bana yenisini yolladılar. Yaptığın iş çok iyi saygı duyuyorum ,teşekürler . Benim için Özel alet,edavat gerekli ve de masraflı. Türk atasözü derki "attığın taş ürküttüğün kuşa değecek) 😃
Ответитьvauv hiç aklıma gelmezdi modül arızası. tebrikler...👋
ОтветитьHey Mate, have three of this. Thanks to you, one is working again!
The two Others have just 2,4V on the Regulator... Do you know the Problem?
hello any idea how to reset pin to this type of battery? i have 2 baterry with forgoten password i cant use it because there are bloked
ОтветитьI had the same problem and in a discussion on another PARKSIDE battery repair video I got the same tip about the BT module, 3.3V regulator and 20 ohm resistor.
I used the HT7133 stabilizer, input voltage up to 28V, although only 30 mA. But I measured the board's power draw - when the 3 led charge status indicators were lit, about 12 mA (corresponds to the video here). After 10 seconds the LEDs went off, the draw was approx 5 mA and after another 10 seconds the idle state - approx 70 uA.
I haven't found a replacement BT7L module (only different types), but it's not necessary to have it there. It's just not a "smart" battery (perhaps all the better, a component that is not in the device cannot cause a malfunction).
I wonder why these BT modules short out so often (it's a pretty widespread problem). I can think of the possibility of a voltage spike on the tool motor going through the stabilizer and causing damage to the 3.3V branch ...
Just my reasoning.
Nota 0, o multimetro nao é parkside
ОтветитьErcan please, what is the exact type of the 200ohm resistor ? 0805 or 1206 ? e24 or e96 ?
ОтветитьI put this regulator 7533-1 and the battery not working with new resister 20 ohm ... can you help ...?
ОтветитьThe best repair tutorial for this type of batteries, in my experience they overcharge without the module, anyone whith the same experience?
Ответить