Комментарии:
Thanks John. You're video helped me a lot. I had completely forgotten how to set all this up. Much appreciated.
ОтветитьMany thanks for this excellent video, I have setup Rqly for signal strength on my quad.
Can you tell me if Is possible to set up a sound warning when Rqly is low as I will be wearing FPV goggles, thanks again.
Very useful setup tips. How u apply clock on between the trims and on telemetry page header?
ОтветитьAfter soldering the RX pins, binding everything, and testing the PMW channels with servos, I decided to check the telemetry screen, and no VBatt! After watching your video everything is working as intended. Thank you!
ОтветитьHow do configure the main screen? I have a Zorro and on the main screen I only see the reception bars.
ОтветитьWas just about to get myself the RadioLink AT10 until I saw your other content about it. I'm just considering now the Boxer, doest it have RX sensors to show Flight Baterry voltage telemetry?
ОтветитьWhy does my RSSI only displaying positive? If I have the radio right up next to the quad, it will display 0 but not go into the negatives and then when I start walking away, the number starts to get more and more positive
ОтветитьHelpful indeed. Thanks!
Ответитьhi
how can i display actual time on main screen with the stick&pots and how to display time&timer on top bar?
Thank you...
ОтветитьThanks for this. I've had my Boxer for about a month and really enjoy it. There are a few things that are different on the boxer b&w screen that other videos don't cover. Thanks for both videos 👍
ОтветитьHi. i am wondering how did you set time to show in the home page? Is that only available in 2.9?
ОтветитьThanks for the video! I have some questions - I'm just getting into RC and I'm thinking that I should go with the Boxer as is has a bunch of channels and knobs, high transmit power, and supports telemetry. I plan to work in Ardupilot with a Pixhawk/controller that can run Arduplane and am wondering:
- How to find a receiver compatible with the Boxer and supports sending it the telemetry like you've shown, and support SBUS/PPM for the flight controller? Or is an SBUS/PPM on the receiver what sends telemetry?
- Does the Boxer work with SBUS or PPM, or is that up to the receiver I choose?
- Can Ardupilot even send telemetry back to the Boxer or is that an iNav thing? Thanks!
Hey , thanks a lot John! So helpful. Do you know if there is any way to show GPS-Coordinates as Decimals and not as usual as degrees, minutes, seconds?
ОтветитьI wish I had seen this great video a few months ago when I was trying to set up some telemetry screens on a TX12; I managed to muddle my way through it in the end. However, I am curious how you got the RSSI value to display in the bottom bar of a few of your telemetry screens?
ОтветитьI literally just set this up on my jumper t pro yesterday but I used the inav lua script, I had no idea I could display the telem without the Lua thankyou, I struggled to get the Lua to display and had to update the radio, I wish I just did this instead so for the record this works for the jumper t pro aswell add it to the title because no one has videos speaking in English talking about how to get telem on the tpro the button layout is a little different but easy enough to figure out. Also elrs the rqly is I believe lq of telemetry tqly I think is the same as the lq you have in osd
ОтветитьI need to show the telemetry screen as the default screen after the radio turned on. No need to push "TELE" button to show the telemetry data everytime. Hope the devs is listening.
ОтветитьHaving recently treated myself to a Boxer, this is extremely helpful. Thanks John, amazing work as always!
ОтветитьI found the customizable topbar of the taranis screen really helpful, can't understand why there isn't such a feature for the smaller 128x64 screens...
ОтветитьHi. im using QX7 ACCESS radio. i have issue binding with Radiomaster R88 V2 receiver which supports ACCST D16. im unable to bind to this receiver. i tried updating the ISRM on the radio but still unable to bind with R88 V2 receiver. is there any solution or fix? i tried to downgrade the ISRM to qx7 access ISRM version 1.1.3. and it got bound. but i can notice some packet loss while moving the servos. Does separate firmware for R88 receivers exist? to support ACCST D16 (V2)?
ОтветитьNice
Ответить