Комментарии:
how to calibrate pir sensor?
ОтветитьThankyou ❤
Ответитьgreat codes! it works with no problem. however, when i add nrf24l01 module to it (the setup in the video being the transmitter) it doesn't detect motion and the led and buzzers are not working. is there anything else i could do?
ОтветитьI tried mine pir sensor isn't working
ОтветитьWe don't have gnd buzzer is it necessary
ОтветитьHey did you update the code
Ответитьi connected as it is but not working
Ответитьgood, but I want it to make the sound if the motion is not moved for 5 seconds
Ответитьhi i messaged you on instagram
Ответитьgive me code
Ответитьwhy does the buzzer keep chirping? what if it just buzzes and then stops after a few seconds, then it just buzzes again when something is detected.
Ответитьit's now working. Thanks a lot
ОтветитьHello, do I need to adjust the sensitivity of my motion sensor, cause after calibration, the code may falsely indicate that motion has been detected after 30 seconds even when there is no actual motion present
Ответитьit works only in india
Ответить100% Working
Amazing 😍
Hi! is it possible that if the sensor sensed gesture it triggers the LED to On first and if f the gesture is in repeatable state after 5 sec the buzzer will be on as well. and there is a scenario that the sensor sensed gesture let's say for just only 1 sec it triggers the LED only but not the buzzer? please help me for this sir. 🙏🙏
ОтветитьLCD+ buzzer+ sensor pir
pls 🙏🙏🙏
Would it be possible to have the motion sensor trigger a hotkey on a computer if still plugged in?
Ответитьive watched thisl ike 5 times now WHY WONT IT WORK AAAA
Ответитьc est une des meilleures vidéos d arduino! elle est parfaite...
Ответитьsir In my code, low, high, input, output texts appear colorless and my circuit did not work. I think my library is missing where can I find it?
ОтветитьI have some problems this project
I sent u msg on Instagram
did you have schematic circuit diagram??
Ответитьprovide link for code and circuit diagram
ОтветитьIs the applying code is compulsory?
Ответитьon which software you are running this Arduino code,plz help
ОтветитьWhat is the prize of the products which are used in this project? Can any one of you help...
Ответитьis it possible to use an LED matrix instead of the LED light? I.E when there is no motion the LED matrix shows RED light but when motion occurs, LED Shows green light and buzzes? Is this possible and if so could you explain how?
ОтветитьDoes this whole circuit run on a 12v battery?
Ответитьcan I get semulation of this project
Ответитьkalo minta buatin sistem minimum (yg di solder manual untuk tugas) bayar berapa bang ?
ОтветитьI am not getting the output how should I contact you?
ОтветитьThanks a lot for this project. But the buzzer takes to long to stop the sound. How can i adjust the timing?
ОтветитьHi is it okay if I use a long bread board and any led?
ОтветитьWhat do I do if loading the code activates and stays ringing but never turns off
ОтветитьCan. I get the code the one in description is not working
ОтветитьNot working
ОтветитьProgram code is in which language
ОтветитьBro can send me code which is showed in video the one which u uploaded is different and not works properly
Ответитьcan i use 100ohm instead of 220 ohm
Ответитьif sold, how much is it?
Ответить