Комментарии:
Old circuit.
ОтветитьCan fine the PCB layout
ОтветитьMuchas gracias, ya lo probé y funciona al 100 % 👏👏👏
ОтветитьTook a long time to actually find this circuit. Considering it's very common application, is not that good. So well done for this article.
Ответитьනියමයි.ඔෆ් අවස්තාවේදි කොපමන් දරාවක් ගන්නවද ?
ОтветитьCheapest expensive more thanks
Very simple very important surkit dayagram thanks
Removed the LED and associated Resistor and the output from the Collector on the second NPN works well on digital pins on the Arduino. I did find it interesting the using a logic probe on this same output kept the output low all the time.
ОтветитьJust use a bi stable multivibrator
ОтветитьResistance #9؟
ОтветитьVery good video and example! Thank You!
ОтветитьHas anyone figure out yet how circulation pump motor works? I know it uses gate driver in IC to drive gates in IGBT. It is 3 phase too. pump name Wilo made in sweden or something. Same shit is in those compressor heater/cooler, the fans are run by PMM thats driven by weird pwm using gate drivers and IGBT. I wan to make them run on 12 or 24v DC.
Any smart person here? I could even pay if you know where to tap the pcb.
What if I wanted to use it with a 12v or 16v, what will change
Ответить🇧🇷👏🇧🇷👏..... SHOW
ОтветитьIf youknew anything about switches, you could have just bought the correct switch.
Ответитьthis circuit doesn't work in simulation
ОтветитьThere is one disadvantage in the circuit suppose you want to turn on the circuit using external transistor signal With High and Ground signal than it's not helpful for you .
ОтветитьPlease help is there any ic with that function?
ОтветитьCan this be used in noisy circuits like car electrics?
Ответитьthank you veery much you are amamzing
Ответитьif i want to use supply voltage 24v, is there any components should be replaced?
ОтветитьI need to power up a 6v XHP70 LED with 2 X 18650 Battery. What should I do?
Ответитьif i supply 15V, can i change in circuit ?
ОтветитьThank you.but still confuse about the process.
ОтветитьCan you tell the current direction at the switch at two stage, 1st press and 2nd press. From you video, it seem that at first press, At the Switch, current flows from left to right and at 2nd Press, current flows from right to left. Please help explain with thanks!
Ответитьi want pcb file plz
ОтветитьCan it also be built using Opamp reducing the other passive. components ?
ОтветитьVery very Interesting circuit without uC
ОтветитьWill this work with 12v?
ОтветитьWhen i connect a motor instead of led doesent work why?
ОтветитьI did a very similar change to the R5 in order to make it working properly. Lower value made it easier for the bottom transistor to close
Ответитьwant to used AC220
ОтветитьVery nice I subbed ya.
Ответитьachive link not working
ОтветитьThankyou very much
ОтветитьGreat circuit and thank you for the detailed explanation of the workings of the circuit. I learnt a lot.
ОтветитьAny change if 5v
ОтветитьNice... Explanation thank you
ОтветитьMuy Bonita
ОтветитьCan Bc547 Or Bc548 transistor be used
ОтветитьA D flip flop IC can be used to get the same thing without all these components. the IC is cd4013.
ОтветитьCan i use any npn&pnp transistor?
ОтветитьHi. Can we replace the push button by a trigger from micro controller. Thank you.
ОтветитьAwesome video! The simplest circuits are often the most interesting!
ОтветитьLiterally an all Resistor Circuit!
ОтветитьCan I use bc547 transistors
ОтветитьCan you send the circuit?
Ответитьcan you give me PCB board pattern and mounting plan ?
Ответитьdoes the capacitor have to be polarized?
Ответитьwhat is the maximum current
ОтветитьVery very thanks
Ответить