TBS Crossfire Series: TBS Nano Rx Setup Tips

thank you for reading this. I have a quick question. Can these TBS nano's be used to control and fly a stand 4 channel RC plane/jet?

IT IS 2022 NOW. I HAVE INVESTED IN CROSSFIRE EVEN THOU I HAD SOME LRS AND THAT IS WHAT I WANT TO USE IT FOR AND MY DRONES. ON MY DRONES EVERYTIME I WANT TO FLY ONE OF THEM I HAVE TO BIND THE THING again every time :) does anyone know why?

I bought the nazgul5 with tbs crossfire and tango2 pro controller but cannot get the thing to bind. so frustrating

Can i bind my micro module tx with a reciever before putting it in the drone ?

Thanks for the great video. I have the crossfire module on my TX16s. When I go to bind my quad, I get Tracer Micro tx which will not bind. Where am I going wrong?

sorry my nano receiver has solid red light non the led and I cannot bind
do you have any suggestion?

Is there a better receiver for a fixed wing aircraft that Im not concerned about weight?

💪💪👊👊

Thanks for video, I'm confused on wiring from nano to f405-wing, I've updated firmware on micro tx v2 4.0.2- nano receiver 1.17. I've wired nano channel out 1 to uart rx1, channel out 2 to tx2 - 5v and ground same uart, no matter what I do it will not connect to any android app such as mission planner or Q controller. My question is should nano channel out 3 and 4 also be wired to a different uart to make this work. Thanks again

Great work... How would I wire a nano receiver adapter( to leave in fuselage) separate from the nano rx ( placed on wing ).

cannot trim channels . Elevators lock in one direction and can't be trimmed back . I'm using with a simple stabilizer to avoid the complexities of flight controllers .
Just another mess

question tbs nano rx has a adaptor board haw can i use it properly install and its functions?

Can you point me in the right direction on using this with a fixed wing 4ch foam park flyer?

DO YOU KNOW IF THIS SET UP CAN BE DONE WITH THE FLYSKY RC ? Thanks

Can I use nano for running a 4 channel rc plane?

Was wondering if you have looked at the new TBS nano diversity? i read that it can have its own power supply and produce its own type of GPS with Lon/Lat and RF signal to pin point its location.

Can the SDA and SLC pads on the nano RX be utilized to Run the Magnometer/Barometer on a Compass GPS?

Hi I have a question nano tx updated to 288 nd after that when u go in to crossfire lua scripts nano RX says device killed 101

Hello !prompt please here at me on Crossfire GPS data from the menu of Taranis does not appear I choose detection of new sensors it about nine finds but among them there is no GPS data. but also for some reason telemetry in lua script inav on the remote also does not go though 3D fixation eventually occurs but for some reason the data from the controller flight most likely do not reach the remote in General I do not know what the problem is. you can tell on Crossfire behind on the remote control should be the last menu item displayed GPS data here I do not have them. in the configuration settings of the flight controller, inav has checked the data telemetry feed.What can be done .Where to find the answer that can suggest the ?!prior to that, the lua Script was working fine through the port F which was flying Nicky. Thanks in advance !

I just got my first crossfire and have a qx7. I heard you need the upgrade for qx7..but heard also that it is really for the latencies..what is your opinion on this. I have watched you since I started a year and a half ago and trust your honest opinion

I have the 2W model, and its in open region. I have problems with the nano rx, since is givingme very low range and it disconects. it wont bind in 915 mhz just in 800mhz.... help

I hope you did the qx7 mod to run the crossfire! To run 400000 baud rate otherwise that qx7 won’t run crossfire correctly and things will go bad and people can get hurt😬

Hi IV done a DX9 mod for crossfire bind ok both had green light on nano and tx turn off and turn on again all working but no green light on crossfire is this normally or do I have a problem

Great series of videos -- I recently integrated the TBS Crossfire setup per Method 1 outlined in the DX9 Crossfire Protocol Instructions (SPMR9910_Crossfire_Instruction document). Everything works great and I was wondering is there any way to get telemetry data on Spekrum transmitter screen (primarily voltage and RSSI). Thanks!

hi painless I just received a rtf oblivion believe me it s not

I may have put myself in the wrong region I tried to push the bind button more then 10 times but I wont let me access the general menu on the tx

with tbs categorical refusal of helping people over the phone or hands on this little quad will be resting in it s nice case that it came with

thank you

Howdi so after sticking a nano rx on a new build and installing fw to a beta version a previous older quad using a v2 micro rx won't bind.. 
Question - do you know if they can use similar fw or you cant use a nano & micro ?

Thanks in advance..

I'm not happy with Crossfire microTX and NanoRX at all. The range is no more than a few meters. Support is not helpful, they just asked the questions I already answered. I hope I get my money back.

I am using a nano on a futaba 16sz, where do you set the output mapping like you have done in the taranis.

All this information EXCEPT the pinout. Lolz However you do a great job regardless

Thank you so much for this! I too had the 2.24 binding bug. Flashing 2.25 Beta sorted everything out perfectly.

Glad TBS is doing well with their niche products.

I have the TBS Tango (Awesome radio) and the Micro TX......... took about 2 min to update firmware and then 30 sec to bind the RX Now to set it up in iNAV

My Micro TX was locked to FCC mode (i.e. not Open). I updated the Micro TX and Nano RX to 2.24 and they would not bind to each other. I updated to 2.25b and all was well.

The Nano RX is lighter than the Immortal T antenna!

What if you got tbs micro modules

Awesome work, man. 😊 I've just watched the first video of the Crossfire series when I saw this one. 😊