Pipe beveling with a cutting torch oxygen actelyne

Ive seen way better

What if you can’t roll the pipe cause it’s welded in place. Maybe show that one

上手くはねーよな？普通にやるやろ？？

I’m a 4th year apprentice plumber. I had to cut 2 6” carbon steel with acetylene torch. I cut the beveled freehand and cleaned it up with a grinder.

Cutting the bevel reduced the time needed to grind a clean bevel, but this is clean! I’ll have to try this next time!

Use a power roller do a masterful job!

Susah mat nak buat HAHAHAHA

I won't lie to kick that horrible.
Always cut going up hill do the start stop by kicking it up on the drop side and feather back in when starting again

為什麼不想只接用切管機切呢！開槽稍微磨一下就好了呀！

Well ain't you special...any 2nd year apprentice is required to be able to do this..

Awesome!

I'll be better if you put the torch tip straight on the line and cut forward at the same angle as if you were cutting with a bevel machine you'll have a cleaner and straight cut . Nice job man

Can’t stand a mfr that drags the file.

Ay que echarle más ganitas

Skill!

I guess this is an old school torch hand style, as a Pipefitter I would just cut it with a bandsaw, or cutting disk, and then bevel it with a grinder. He is still going to have to clean it up with a grinder anyway to prep it to fit up and weld it out.

What did you set your oxy/acel at?

Good jop

Was beveling 18" fixed position today about 1 ft off the ground. Looked about that good maybe a little worse. Helps to have your support hand right near the torch head. Good shit tho, beveling pipe in any position aint no spring breeze

Someone needs to find that fire breathing beaver and put it out of its misery.

Glad I don't have to weld that shit

👍🏾👍🏾not bad grind a smooth landing and its a go once u tack that sucker cool free hand job

What are the advantages of cutting a bevel? I used to be a demo laborer and I would just cut straight in

Да ну на фиг какая хорошая работа, вы что там курите... Дайте ему шлифмашинку...

too fast bro ..u need slowly when cutter.. smooth can be better bevel ..

saddle bend calculate????

Could fit the grinder into that pipe feck the hand file

Hamare pass gass cutter milta hai contract 7505142069

Mucho acetileno

Good hand cutting skill

Looks like a shark took a bite out of the pipe

Welding boss said if u dont look busy u can get ur ass on the unemployment line... someone show these guys what a bevel machine is...

Good job bravo

No está mal para un novato

Métele escuadra haber si quedo escuadrado el corte 🤔

No lo sé rik me parece que le quedó descuadrado el corte 🤔aparte de todo mordido se nota que le falta mucho para aprender a vicelar

Cool. But I get paid by the hour. I like everything to be exact.

Tack it. Weld it. On to the next one.

这不行

I mean I've only started cutting with the oxy acetylene torch but I've already gotten decent enough to bevel. Maybe not professional but I'd say pretty good but I've never tried beveling a pipe. Loved to try.

Sick fucking NASTY🤘🤘🤘🤘🤘GET THAT SHIT!!!

turpijom turpijas

Pierce of shit cut come to me que learnyou how to cut

Nice job! Clearly you've done this before.

what are the actual benefits of cutting with gas instead than with a grinder? Thick material ,yes, but if the material is thin? I dont see benefits.

Not good cuting

slick

Наши монтажники не поваротно лучше режут

А вот эти движения кувалдой меня радуют. И претупление сделает и выравнит пока горячая труба.