Комментарии:
Welcome, my friend. I have a similar type. I wanted to program the remote. I made an incorrect programming error for the gate to go up and down. Can you help me?
ОтветитьHi! Can I erase a BFT Mitto 2 remote and reuse it for another motor? Thank you for your answer!
Ответить2023 and still working thanks 🙏🏻, but I took little bit longer than the video though
ОтветитьVery nice. But whan everything is over. How can i change a speed of opening or closeing of a doors?
ОтветитьGreat video saved me a lot of time and money thanks bud
ОтветитьHow to connect a wifi relay 100-240v on BFT MITTO for smartphone control of the gate? Thank you!
ОтветитьHow do I program the gate to stay open for 60 seconds then close automatically without pressing the remote again? I have a bft cantilever gate
ОтветитьI have an ares ultra 1500 but i cant connect any of my remotes to the motor. I did all the steps and nothing. I never get the message that says release i only get an ok and goes to hidden button. Any ideas on what might be the problem ? Thank you
ОтветитьBulunduğum sitenin yöneticisiyim Urano BT model otomatik kapı sistemi var. BTF kumandayı sizin ki gibi kopyalamaya çalışıyorum ama olmuyor. Yardımcı olur musunuz
ОтветитьThank you so much for this video!! Made it easy as pie to program!!
ОтветитьAnyone has done this BFT system to homelink in a car?
ОтветитьHey can I add a button so I could just open one gate
ОтветитьHey guys, can I program the bft mitto remotes with roger gate system? Or I need a relay? Thanks in advance.
ОтветитьHow did it work use say Error 16 though
ОтветитьExcellent video. Thank you so much!
ОтветитьWOW! What genius came up with that super easy method?
ОтветитьThanks fallows the instructions it works, you have tobe consistent with the process are it will not work.
ОтветитьIt’s showing error 20 how do I solve Sir? Thanks
ОтветитьHuge thanks, the original instructions are impenetrable!
ОтветитьThank you for the usefull tips. Does this also work for BFT Thalia U-Link series?
ОтветитьDuring programming it appeared "KO" instead of "OK 1". Can you help please?
Ответитьthank you
ОтветитьHi,
Awesome videos. Pls can you show me how to delete the remote that has not being used.
Thank you for the video, I'm using this in 2019 and it's still relevant.
Just a note for others: I think you need to be reasonably close to the motor unit of the garage door or sliding door or whatever you have for this to be able to work.
How do you program a button to activate pedestrian mode (where the gate only opens partially)?
ОтветитьThank you very much. This was so easy to follow and it works.
ОтветитьThank you - not intuitive so was struggling until I watched this - touching + and - together :-)
ОтветитьIt doesn’t work on my BFT. My screen is always on with « Suc ».
Whenever I press ok twice, it shows F1 on the screen..
HELP !
Hi
Please need a help.
Suddenly Gate (btf) open not closing, gives on digital screen (photo).
So I connect 21with 24, working perfectly without photocell, I bought new photocell, install it, Same problem even with new one, Same read on screen ( photo).any advice please?
Thanks
Many Thanks
ОтветитьVery useful. It works perfectly !!
ОтветитьExcellent! It worked fine! Thanks a lot sir! By the way, for those who have an oval remote, the hidden button is inside the little hole behind the remote, use a tooth pick to press it then release.
ОтветитьThank you create job saving more than 70$
Ответитьthank you very much. I'm french, and I did not find a french clear explanation. but yours is so good. I managed to programme my remotes. thanks a lot
Ответитьthank you! worcks.
ОтветитьThanks iv done this a few times but it can be months of a gap iv to pair off 10 to a gate tomorrow & this was a helpful refresher
ОтветитьHi I know the video it's old and all but I have a question. How can I change the time that the gate stays open? The problem I'm having is that it won't stay open for mor then one second and that's not enough time to hit the photocell. Thank you I hope you can help
Ответить