ANSYS Fluent Tutorial | Particle Flow Simulation | Discrete Phase Model(DPM) in ANSYS Fluent | #CFD

Greetings! I have struck in developing a reaction between Methane and Steam in CFD. If you have any content on the chemical reaction at elevated temperature and pressure using species transport and Chemkin thermodynamic, surface reaction files, kindly revert back.

i am wondering whether 3d have any different with 2d settings.

Hello, hope you are well and thank you for your video. Is it possible to map the sum of particle volume fraction and the sum of the particle volume at each cell? This is so I can use it as a part of a field function along with other constants and displaying the contour for it. Would appreciate your help.

Thank you!

I cannot Understand anything regarding gradient, and other variables at all. Is there any study material you can suggest me so that I can get an idea regarding Partical flow simulation? pls?

Please, In what order can I follow your videos to comprehensively learn ANSYS Fluent from the scratch. I need to learn it for my finals project for the numerical simulation of atmospheric water generator.

If you cannot click the data file quantities, try this:
go File --> Preferences --> General: Default Format for I/O --> Change it to Legacy --> OK

Sir, can a soft object burst after collision with a stable, sharp object due to fluid pressure in the Ansys workbench? Example - ball collision on a needle-type stable object in a fluid

Is there any erosion model tutorial with DPM??

How to get particle velocity in fluent?

Thanks, very useful lecture .

How to use the "Particle mass loading" value in Ansys fluent for a gas-particle flow??

Actually, I want to simulate a jet stream from orifice geometry(pressure atomizer) with liquid water (multi-phase - vapor) later the jet stream should break into DPM droplets so that I can estimate droplet size. Is there any way where I can couple these two, multi-phase and DPM in Ansys
Thank You

Please I need nanoparticles to the phase change materials

Dear sir, Can you please tell how to plot impact angle and impact velocity contour in CFD Post. I am using OKA erosion model.

How can I measure the volume of droplet in ansys fluent?

I AM GETTING FLOATING POINT EXCEPTION ERROR

Hello Sir May you explain little bit more about injections why we create injections. what's its purpose?

My DATA file quantities option is inactive ..!!! Can you please help

Please explain the physical meaning of the options in granular properties and all other options we are using. Otherwise it becomes hard to understand what we are doing actually.

My "data file quantities" in Ansys Fluent is inactivated even if I completed initialization. Can you help me please?

Hello, Thanks for nice video. May I ask why "Add Frozen" in the operation tab of design modeler ?

Hi, I'm a begginer learning Ansys fluent. May I have some simple simulations related to steady state conditions. Thanks n regards!!

Thank you so math for this vedio ,i want to now how to calculate spread parameter

Please how to calculate thé nombre if stream

Is it possible to make particle sedimentation and inlet airflow move particles which is 0 velocity at t=0?

Sir please make video on asphaltene precipitation by using Ansys fluent

How can i change the air flow into a fluid flow? eg kerosene

Sir during 96% simulation I am getting floating point exception. What to do please help me

hi
In CFD-post, only 10 variable is available in contour-geometry. I could not find variable such as air velocity, DPM magnitude, concentration, particle diameter, etc.,
sometime appears and sometimes not.
is here a problem ?

Thanks a lot!.

ive been wondering if i were to run a multiphase model nanofluid with al2o3 as solid. should i also follow this way? because with discrete off i cant create aluminiu oxide under fluid cell

Thank you so much for the great video! Is it possible to have a single inlet for multiple fluids with different volume fractions? say oil, water, and sand, so that the particle, which is the sand can be injected from the inlet. Thank you in anticipation of your kind response.

Thank you so much.

Can u share a simple video tutorial on airborne dust simulation in underground tunnel ?

say tunnel dimension 5mX5m and having length of 100m.
airflow is 50 m3/s.
dust injection rate at a point source in the tunnel may be 0.1g/s.

Generally how much time does it take to complete the solution ?

Your videos are best as always. I'll suggest one topic see if you can make simulation video on this

Injection of vaporized water inside a cylindrical chamber with air flowing through inlet. Explanation: there is cylindrical chamber with inlet at one end and outlet at other. Air is flowing through that chamber. There is one injector which injects vaporized water (steam). First the water flows in liquid form and during injection it changes its state to gaseous.

Thanks sir for your educative tutorial video. Sir, I will appreciate where you to do a tutorial on multiphase particles using sand and water to monitor the leakage and the flow. Thanks

Sir plese provide number

sir i have question, after initalization popup message said I don't have data and in your video you goes after that file and click data file quantities, that data file quantities are not working in my side, kindly suggest if I am doing mistake.

Sir, can I install both solidworks and ansys on 8gb laptop, if I use 1 software at one time

it is very nice and instructive. i have a question, is there a way to build a UDF code to calculate the particle history?

very good, thanks