Комментарии:
Great Video thanks!!!
ОтветитьHi! I have a question!
I dont understand why the volts, minvolts and maxvolts are calculated like ("value"*5.0)/1024.
If you explain it to me I would be grateful. Thank you
Can this be used without Arduino?
Ответитьthis sensor suks almost no changes on analog input even when starting from almost dead silence to a crazy LOUD clapping (btw removed even the delay and dumped all the values to a file still no significant change to know when there is some sound...)
Ответитьwhere can I finde it
ОтветитьI can't understand how this device can be useful. The analog out does not change if you speak or if you clap your hands. You can get significative variations only blowing in the mic, tapping on the mic or with anything else that applies a "physical pressure" to the mic itself. Probably it's because the analog out is a not-amplificated signal. Anyone else with the same experience ?
Ответить;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; yeeeee "MISTAKES" can desolved with a lowerCASE PRINGELS-MIC-CASE ;;;;;;;;; ;;;; ;::::::::::::::: NOW WE CAN HEAR DOTS COLONS ..........OHHHH mistaks ::::::::::
Ответитьthx YEEAAAA we can learn COLORcables imitatation DIY fingerjoys!?
Ответить👍❤️
Ответитьcan you please share your email?
i need some help for my project
hey milan
ОтветитьI have a problem, one components already have Ao to work. Can i put it in any other analog??
ОтветитьAnd all of that would work with Any Input right?
ОтветитьDoes this module distinguish a certain sound or just any sound?
Ответитьis line 47 apart of the code, if so what does the rest of it say?
ОтветитьHi. Could anybody please post a build of Arduino decibel meter for an Airgun with shown Max last reading. Small size would be preferable, possibly Arduino Nano and Oled screen. Most Android Phone Apps don't work correctly as the phone kills the Microphone sensitivity automatically and sampling isn't fast enough. Thanks in advance.
ОтветитьVery helpful video. Thanks!!!!
ОтветитьCan we record sound using this sensor?
ОтветитьHallo sir.I am making this experiment.I have connected my LED to pin no.4 of Arduino and the output of sensor to A0.But what is happening with me is that when I am making sound,the LED of sound sensor is blinking but the LED of breadboard is not blinking.Sir what can be the problem? I have connected the anode of the LED to a wire and that wire is connected to D4 pin and the cathode is connected to ground via a resistor.
Sir please solve my problem.
Hello sir, i want to use three pins of KY-038(DO,G and +), just like KY037. Will this work with only three pins? Can you please tell me which three pins are same in KY-038 module as compare to KY-037. Actually I don’t have much knowledge about arduino and electronics, so I don’t know about this thing.
Ответитьwell done
ОтветитьHow can I use this in a system that deters barking dogs? I currently have a system I wired together that runs high pitch piezo tweeter speakers on a remote but that doesn't work when I'm not home to activate it. The over the counter bark deterrents are useless. I need it to stay on for 30 seconds when it detects noise but no shut off when it detects the second bark. Any ideas?
ОтветитьThanks for clearing up my mess. I thought it was a sensor fault until I found this amazing video :)
ОтветитьHow can i use this sound sensor for more applications with different power consumption?
Ответить... I couldn't hear what you were saying after you tidied up the code, until you indented line 18 .. 🤤
ОтветитьUsed your code to try it...and just doesn't work
Circuit is very simple i'm totally sure I've done it well
So...just don't understand why both leds are turned on all the time
all i want to do is get my sound system to move a servo but i cant find anything, anyone know how to accomplish?
ОтветитьIs there a sensor that detects sounds above 20kHz?
ОтветитьReally appreciate the callibration part and pointing out the correct internal schematics. This module was driving me crazy and I thought it was just a useless piece of junk...
ОтветитьGreat explanation and well-made video! Would you happen to know how to get a frequency reading from the KY-038? I'd really appreciate it as I'm looking to build a guitar tuner for a project.
ОтветитьSuper clear explanation 👌🏽
Well done bro 👍🏽
Our ky-038 don't light the L2 anymore were very dead 😭 😭 is there anything we can do ???
ОтветитьWhat is the minimum input voltage for this sound sensor ?. My board does not have 5 volt it only can supply 3.3 volt . If it cannot operate on 3.3volt i think , i need DC-DC boost converter/linear regulator to boost to 5 volt
ОтветитьI have researched this for quite sometime now, used a couple of codes and setups online as well as this video but can't seem to get the desired result. So what's happening is when the code is uploaded as well as the exact same setup of the sensor writing to the Arduino LED on pin 13, the sensor doesn't output anything despite my earnest attempts of clapping. Following one of the tutorials, it suggested to tweak the potentiometer until the 'LED2' starts flickering. So I have it set on that, and notice that when I clap loudly the LED2 on the sensor flickers on however the Arduino LED (or an external LED with a resistor attached to its anode to ground on a breadboard does not). The Arduino LED / external LED however very rarely responds to my claps whereas LED2 seems to always be responsive although when blowing over the microphone the load LEDs turn on. I can assure you my wiring is the same as a basic setup and heres a pseudo list just in case:
Sensor's D0 ----> Arduino Pin 3
Sensor's A0 ----> Arduino Pin A0
Sensor's V+ ----> Arduino 5V
Sensor's GND ----> Arduino GND
Arduino Pin 13 (onboard LED)
(Arduino Pin 7 ----> external LED)
Any help will be appreciated thanks!
Unfortunately, my example sketch is heavy on the OLED, string manipulation, and kinda light on the KY-038. It tracks the maximum and minimum values and shows a bar graph. I revised the sketch after making the video. The revised version is available on GitHub (see link in show notes).
ОтветитьHow can I get Decibel value from the Analog pin and display to the serial monitor ? Pleas Help
Ответитьi got lesson 20 as follow; sound sensor example.HUh?
ОтветитьWhy the analog output has a same value even our voice is loud and low?
Ответитьthis video made things way better, i am not sure why the documentation isn't up to par. It was really annoying trying to find out how to set this up before i got to your video. GREAT JOB!
Ответить