Metal Detector Coils, how to make the worlds best coils.

very love chanell❤❤❤

❤❤❤❤ good men

Could you make me a 15 inch search coil for my Fisher CZ 6 metal detector? How much would you charge for a 15 inch diameter search coil for my Fisher CZ 6 metal detector? I want to use it for deep cache hunting and relic hunting.

Do you actually have a video going through the coil design and manufacture? That would be very helpful.

Hi there! This information is pure gold!

I've been building the surf pi detector and I don't have access to 0.25mm2 tinned copper core

Is it better for the coil to go stranded tinned plated Copper 0.22mm2
or 0.25mm2 stranded copper core?

The guy who sold the pcb recomended
30 turns of 23AWG with a coil inner diamer of 15.3 to get 1.5 Ohms and 310 uH
23 turns of 23AWG with inner diameter of 25.3 to get 1.7 Ohms and 340 uH

Thank you for reading this! It will help a lot!

That was good!! You should team up with Nuggetfinder in a partnership to make metal detector coils.

What was your ratio of carbon and graphite? What did you add the graphite and carbon to make the solution to apply to the coil? Did you use a spray gun and how to do the four quadrant taping without making a mess of things? I read below you use a blender to get it finer. Was the blender typical one purchase at a store? The goal is 80 to 120 ohms per/sq.inch. Best I have done is about 600 ohm with many coatings shielding. This has been good info about ML coils.

I watch that video 20time its very good

Hello First, thanks for all the valuable information that you share with us I have a question please help me I want to make a GPX file, not a small file, at least 30 inches, but I don't know much about measuring resistance, hertz, and others. I had an idea and before implementing it I want an answer from you If you take two coils, for example, two coils of 18, and remove the wires and connect them to each other, and create a disk of 18 x 2 = 36 Will it work ^^ Just connect the wire of the two disks to each other and understand in a circle the size of the disks whether it works or not Thank you very much If it does not work, I hope that you have a fixed table for a specific number of turns and a specific thickness of the wire for a diameter greater than 20 inches. Please advise me, thank you very much.

Hi...about cabel of coil what made from? I mean what element get in cabel ..... thanks☺️

Tuan yang baik, coba anda membahas dan mempelajari tentang coil DOD yang di pakai gpz7000 untuk di pakai di gpx4500 ,vpx5000 , apakah itu akan lebih bagus penggunaanya di lapangan berbatu panas 🙏🙏🙏

Thanks for the info. How did you inserted the litz into the polypropylene sleeve?

In your opinion, in gpx5000, in wet sandy ground that has a little salt, with a 25 inch mono nugget finder coil, which option has the most effect on the silence of the device? Thank you, please explain what is the solution for such fields.

Hi Woody
Thanks for this information.
Please what is the number of turns in this coil (18 inch).

YAY

Hi Woody
Great information, I will try your methodology. My few tries at making graphite paint has resulted with high resistance 600 to 900 ohms. Any advice on reducing the resistance would be much appreciated.
Thank you for your videos and have a good day,
Chet

Begitulah mono coil, saya sudah mencoba membuat sendiri coil untuk mesin gdx8000 china , mulai dari ukuran kecil sampai ukuran besar dan semua bisa digunakan🙏

Thanks for your good information about metal detectors .i have a question about what is the ZVT technology wich used in GPZ of mainlap

Hello, do you have a website, or email that I can contact to discuss mods for my gpx 5000, and gold monster 1000? Thank you. Great video, I'll be continuing to watch more.

Boa informação

Hi thanks alot alot alot.. i waiting this informatiom for along time thanks to you and to your son divd ☺️☺️☺️☺️

When I put the coiltek 6 file on my gpx 5000, does it reach the sensitivity ratio like the Monster gold device