RSLogix 5000 PID Setup and Tuning

Thank You

What is the %output meaning in this PID block ?

if you have sample or acd file it will be very good for us,anyway thanks for this helpfulvideo

Truly speaking, this is la creme de la creme. Congrats Shane

Hello Shane,
Is there a rational method to determine what should be changed, by how much and in which direction. It sounds as if we are making changes without any prior guidance or reason, and then if needed, and as often as needed, we are reversing these changes or acting on other parameters, or for that matter, reinforcing the previously made changes? There is a lot of guesswork that is not easily analyzed or planned for in this approach to tunning PID.
Thanks anyway for sharing with us your expertise

Ola Shane! Ótimo vídeo! Abraço do Brasil 🇧🇷

Very well done PID definition and instruction.

i enjoyed this video alot wish you do more pid loops awesome work on showing us

Hey Shane, I was wondering if a drive could cause a velocity error? I have a machine with 6 axis all set up the same. Only one axis has a high velocity error. We took apart conveyor and inspection all bearing and gearbox? Didn’t find anything to cause the velocity to spike. Could it be a bad drive. They are 25 plus years old?

I set the logic diagram and pid setting exactly the same as yours, but when i put the PID in Auto Operation then the Output strike to 100%, the curve move fast to 2000 (SP set to 250), is there I missed for something here?

What is the difference between Independent and Dependent mode ?

Just wanted to add my 2 cents given I just went through a troubleshooting exercise with Rockwell. For Logix5000 they do not recommend having any conditions on the PID instruction rung, rather just keeping the instruction inside of a Period Task with the same interval as the Loop Update Time.

Excelent.

Sir, in CONFIGURATION of PID what is role of NO BIAS CALCULATION.
does it effect the oscillation.

Hi Shane,
i want to congratulate you to this Video. I just found it while I was searching some Themes for tutorial Videos. The reason is that I´m working for the German Rockwell Distributer and make Videotutorials in German.
This Video is for sure one of the best about Tuning a PID Loop.

someone give him a Nobel prize, please.

Best video and great work but need to zoom in the screen little bit

Hi Shane very nice video, have you got any video where explains how to configure the simulate PV rung?

Good video. Very informative. I am trying to control the PH of a water treatment system. My tolerances are pretty wide so I don't have to get it exact. What is the difference between the Process Variable and the Control Variable? Any tips on using a PID loop in RSLogix5000 with the PH as a process variable to control a mineral injection motor/pump? Upon further research, I have come to the realization that controlling PH is a nonlinear process so it complicates the matter.

hello Shane, i liked your video, i am working in a college project where i need used the module imc in block diagram but i dont know how tune this block, i have the instruction set manual but it doesnt say so much, i need help , please if you know any about that could you help me?

TB1 tag AS YOU HAVE CONFIGURED?

How i can made PID for 3 analog solid state relay connected to 3 heaters ?To keep the temperature on 50 Celsius

Pls update new video

Thanks for sharing. How can you use this if it is a digital output, say to SS Relay controlling a heater with a
Thermocouple as the input?

Can a different formula be put into the compute instruction to allow the PID to simulate a PV - SP control action?

Thanks the answer, could share  one example of routine  for PI ? , and wthat happen with  D gain ?

Is posible use this PID in order to control motor speed of the spooler  (winder or unwinder )? , if is not posible,  which would be the reason ?thansk in advance

LOOP UPDATE TIME ?

When use Auto_Req Or Manual_Req ?

Good video. If you want to nail the parameters first time, every time then I suggest you contact Hank Brittain of OpX Controls. His 3 day classes are the best around.

Best video on PID available till date... well done SIR... great video ...

Really thanks !!

Nice.