Huge Current MOTOR DRIVER BTS7960

What happens if I set the enable pin with a value different of HIGH or LOW ? For exmaole if I set it with a value of 150 ?

Sir can I use 24v adaptor . 50amper

Bonjour cher monsieur, est ce que deux moteurs de 12 volts comme les vôtres peuvent faire marcher un robot de 40 kilogrammes.

How many motors can be use on adruino?

I have burned 3 of those.. with 350W 24V wheelchair motors. From what I have learned this cloud be because of back current. This driver does not have protection from back current. I will experiment next with cytron mdds30. Should be better.

This is 100% how to wire this board. I just duplicated it on a raspberry pi and it worked perfectly. Don't believe the writing on the board, follow the directions laid out here. Thank you for the video!

Can driver burn

Awesome video

Can I use BTS7960 to drive hub motor?

Hello i want to comand two of this motors with rc. Can you explain please

What happen if we put high/low in l_en & r_en?

Best Indian Content 💯
Just Subscribed,Love u❤️

Thank You :)

Hello ,
I have connect ibt bts7960 to wiper motor snd flysky remote control but some time working to move left side and right side and some time moving to one side only ,really i dont know how to fix that

hi sir,
can you please suggest 4 channel bldc motor controller which can be used for 1500w bldc motors

Can i control 2 motors individually using this if not , then what is the best alternative.

What happens if I connect Hall Effect Sensor to input channels?

Can I get the codes

Very good video thank you

Excellent explanation, Sir. Can you mention of any controller like this that can handle two high-current motors same time?

Really appreciate your work for this video !

Excellant demo, but what about the Arduino coding for us who can not do the coding. Blessings

Muchas gracias por la excelente explicación del uso del puente H.

is this good for wiper motor ?

Hi Saravanan,

Read with interest this article and I'm still not sure how it works. How toaActivate the high and low side mosfets to drive the motor.
For simplicity, say I didn't want to use an Arduino { I'm to old to starting code} but simply drive the inputs with +5volts.
If I enable say the l/h chip {INH High} then apply a high to {IN} how do I enable the r/h chip so that the lower mosfet is connected to ground and assuming the l/h chip the top mosfet is connected to the supply rail.
Does it mean that on the r/h chip I enable it {INH High}, will that in turn, turn on the lower mosfet with {IN} low.

I'm at a loss.

Can you help
Thanks
gazza

olá, pode me dizer como inserir um potenciometro na entrada analogica para controlar a velocidade desse motor ? como ficaria o programa? estou fazendo uma bike eletrica e tenho esses componenstes todos mas não tenho conhecimento na programação do arduino. obrigado

I found out that there is a major design flaw with BTS7960. The heat sink is not in direct contact with the IC chips, giving poor thermal conductivity. Robojax channel tests the driver and by applying a 30 amp load for a few minutes, the chips will start to smoke and the boards thermal protection kicks in and shuts down. I suggest flipping the heat sink to the top side with direct contact to the IC chips. Might require hacking the heat sink a little to make it fit.

PLEASE - if you're going to demonstrate powerful high voltage power supplies to folk that might be new to these topics, ALWAYS connect the earth - the earth pin on the power supply is there for a reason. It's not so bad if you end up electrocuting yourself, but don't teach others to do the same.

Other than that - an interesting video.

Great video. Thanks for the explanation. I am going to be using 6 of these controller to control wheelchair motors in a 6 wheel drive "Mars" style rocker-bogie robot.

Please code

Nice ....

Sean Lyon
30分钟前
Sean Lyon
4小时前
Great video! I am making a ball launching machine using a 12V 30W motor and a 16.8 Ah Lithium battery. I need to control the motor through Arduino to run 1 sec then stop for 5 sec and repeat this cycle. Would this motor controller work with this setup? If not, what do you recommend? Thanks

Bts7960 is a bad module. It has no facility to protect mosfets from back emf. I was working with 350watts 24V motor. I used this module,2 modules get burned. Waste of money. Then I made a h bridge with pwm to control my motor.Each module gets burned when I power off the motor.

Is it that module not getting hotter for a long time use ?

Hello

Thank you... super alle info...

Plz do a vedio how to upload 2 codes to Esp 32 board plz

Sema sir super நன்றி

Hello good What is your email? I would like to ask you about an exercise that I have

Nice video

Great 👍👍👍
Thank you

Thanks