Комментарии:
Thanks for the video. Is there a way to wire in a 12v doorbell chime so when the doorbell is swiped on the outside panel, it rings the chime? I tried integrating one but was unsuccessful. I want more than the app to ring, if possible. Also, is there a limit to the number of users I can have on one door?
ОтветитьYou just saved me THOUSANDS of dollars! Thank you!!
Ответитьcan we combine multiple controllers together? great video by the way.
ОтветитьAre you using a dream machine?
ОтветитьI’m also a IT Director and looking to wire our office with ubiquiti. Currently have 2 x 48 port switches, 4 APs, and AP console
ОтветитьHey Lou out of interest can you set it up so each lock is independent. For example a front gate purely for mail etc. But then a front door key pad for entry to the house.
ОтветитьHi Lou and all. I am new to Access. I want to use it to open a gate. I have an Apollo 635 636 gate opener. The existing button is hooked to the board's Gnd and Input connectors (12Volt). How would I connect the Access hub to this board? What ports would I use on the hub to connect to the board? Where can I find this out if you do not know the answer? Thanks. Love your videos.
ОтветитьStill awesome! I can't wait for the new videos - can you talk more about adding a mag lock to the dry terminal? how would that work? Does that mean getting a 1AMP adapter? New to this and just setting it up.
ОтветитьHave you installed the mag locks in a building yet?
ОтветитьHi Lou thanks for the video. Very helpful for my first deployment. Can you tell me where you got those sensors?
ОтветитьHi Lou or anyone, I believe I have run into an amperage issue. Our mag locks take 500 ma and we have a 4 door setup for our main entrance that we want to control from one hub. With four mag locks it ends up being 2 Amps and the locks do not stay energized. Any ideas on what we could do?
ОтветитьHey where did you get that pushbar? We are in florida and we have to have a push bar for each door.
ОтветитьHow did you wire up the power supply with the lock?
ОтветитьThat was a super simple explanation with everything I needed to know.
Thank you so much for this video!
💪😉👍
So can you have 2 doors run separately?
ОтветитьHey Lou, I use your video to setup my door access. My question is, I have the Bosch ds150I motion sensor and cant figure out the wiring, Can you help me out with REX. thanks
ОтветитьSo you know if the "request to enter" could follow a schedule?
ОтветитьHey @Lou FIlla, I have question. For the push button. Does it open when you use the key? I didn't see that part.
ОтветитьHi Lou, I want to do something similar but I want to unlock specific locks with my access readers. Basically I have the same setup as you, 2 access readers, 2 door locks, 1 access hub. Is it possible to tell the system access reader #1 unlocks only lock #1, and access reader #2 unlocks only lock #2 with only 1 access hub? Thank you!
ОтветитьIs it possible to do a panic button that will lock a door that is always open? I have a client with 2 doors and wants to lock the inner door incase of a threat (govt office)
ОтветитьHi Lou, nice video! I am St. Louis too and building a new home and want to use Ubiquiti door and camera system. Could I pay you a consulting fee to help me design it properly? Thanks, Tom.
ОтветитьDoes anyone know how many hubs and locks the POE++ can power?
Ответитьthanks Lou, we were looking at the upiquiti and were 'guessing' that we could use one door access system to manage two doors. We have a series of bays that have a front entrance and then another door in the back. If you wire both the front and the back doors to the same control when you unlock the front door it is going to unluck the back door at the same time. SO as long as it is low risk to have the second door also unluck this would work well? See that the video was from last year, how has the installation gone at your facility?
ОтветитьHi Lou,
Good video, could you list the hardware you used? I'd be curious on the 300/600 door locks as well as motion sensors you used. Door bell and UNIFI products your call.
Great video, thanks
One question : Door sensor : do they output 12V to REX ?
REX is expecting 12V signal or this vill damage it ?
If I'm listening to this correctly you can use one hub to control a double door access entry. Meaning I can use one hub to control two magnets is that correct?
ОтветитьAwesome video Lou! Can you advise what 12v power supply you used to power the second maglock?
ОтветитьГде у него выход на аварийно разблокировку ?
ОтветитьЕсли если использовать электромеханический замок , и подключить коньку аварийной разблокировки двери( механическую) то это все просто выйдет из строя
ОтветитьThanks for sharing
ОтветитьHi. This is pretty cool. I was just looking for a system for small private school here in NYC and all the other videos I've seen about ubiquiti door access have been single unit reviews mostly.
Anyway to connect? I want to install a system for 3 doors here at our place. We have an old Dahua system installed by a previous hobbyist IT guy thats beginning to fail after almost a decade.
Wanted to re-use as much as I could (door strikes, ethernet wiring, etc.)
one other big problem is most poe switches will not drive that hub
ОтветитьLets say now you install that camera on front door, and an attacker rocks up with a high voltage power supply, or a taser stun gun and zaps the camera? will it blow up the system crash the hub and kill the power to the magnetic locks. ? the camera has a cat5 cable, smash camera from wall, rip out cable and apply 33kvac between cat5 cable and ground? blowup the whole system including the expensive dream machine. They have movs? that will not stop this type of attack thou i bet?
Ответитьwow bro, you open my mind with this setting, my question now is Can i add to the system any ubiquiti Camera or it’s just the one they show in the instructions. I want to connect a G4.
Ответитьsay there are 2 doors one after another can I have it so there is a long enough time delay, allowing me to open the door
ОтветитьSo an access granted opens two (2) doors simultaneously?
ОтветитьHi Lou can you unlock Multiple Door without having to add Power ffor the second one? if yes can you show how to do the wiring ? thank you
Ответитьsubscribed - i planning this for my school hopefully during the summer not many techs/vendors know how this works yet. figuring it out
ОтветитьIt is still a single door controller.
ОтветитьGreat video. How could a person wire a doorbell chime to a system like this?
ОтветитьThanks for the video. Question - currently run unifi in my house and i have an old alarm system. I only use it for self monitoring and not to a service. Was thinking of switching to the unifi access but I have about 12 windows and 4 doors. The windows are your simple magnetic contacts. With my alarm system they each go into a zone to know if its opened or closed. I have not seen much about this mentioned but do you know if unifi works in this sort of way? would i be able to tell which window might be open with the simple contacts?
Ответить