Комментарии:
Thanks for the instruction tutorial. Only thing that it was saying double talk on the parts and tools used.
ОтветитьWhat do these then plug into? I need to join 2 coax cables.
ОтветитьThe width of the prep tool is such that, by lining the end of the coaxial cable to the edge of the notch, the "stinger" (the cleaned center conductor) will be the proper length.
When selecting tools, I opted to go with higher end models that don't require adjustments (Cable Prep's "Super CPT Cable Stripping Tool" and a "Cable Pro" LCCT-S59-11). Admittedly overkill & expensive for most people, but they work extremely well. 🙂
Use of tri-shielded and quad-shielded cables will require a bit more preparation than dual shielded cables. Tri-shield RG6 is fine for most residential applications, while quad is good for installations where interference is a problem.
All in all, a fine video!
Note: As said in the video.
These connectors are for DUAL shield cable. Will not work with QUAD shield cable due to thickness of cable.
Termination process is slightly different for QUAD shield cable also.
Much appreciated.
ОтветитьThanks for the video. It helped me
ОтветитьWell paced and thorough.
ОтветитьThe outer mesh is a conductor.
ОтветитьHave these compression style connectors mostly replaced the hexagonal kind you used to crimp?
ОтветитьThanks for the video! I subscribed
ОтветитьGreat video. I like the way you do your vids, no BS and you know what you're doing. For some I'd like to add a cpl of tricks / hints. Make sure there is no metal on the dialectic after you strip the coax. Make sure there is no dialectic residue on the copper center conductor, some cheaper coax will leave a little on it which can give you issues. The dialectic can and should stick out of the connector about 1/32 to 1/16", if it's flush you stand a chance of it backing down some. If your coax is stiff you can heat it a little before you crimp to help the connector slide on easier. you can let the coax extend further out of the stripper when stripping and then cut to length after crimping. One more... don't expect the center conductor to be solid copper. All high frequency coax is copper clad steel wire.
ОтветитьGood job….
ОтветитьLove that compression...so satisfying when there's resistance...
Ответитьdid the crimp hold?
ОтветитьHow do you connect the two ends of the co-ax together?
ОтветитьGood video bro 🤝
ОтветитьDoes it make any difference if you use rotate the v-block in the stripper and use the RG6 setting, also is it important to strip away the foil and fold the inner mesh down as well?
ОтветитьThanks
ОтветитьThank you guy 🙏
ОтветитьThanks
ОтветитьGreat no-Nonsense video !
ОтветитьGood video, i'm redoing the routing of some of my coax with new tomorrow and i have had the same kit a couple of years now but i pulled up your video cause it's been a while since i'v used it. Thanks
ОтветитьThanks for the video; very informative. My kit from Amazon didn't include instructions so your vid was very useful.
ОтветитьThank you. I ordered the exact same tool from Amazon BUT it came without instructions. Thanks to you all is good. 😊
ОтветитьThanks for the upload. I bought the same kit a couple years ago for full coax connect throughout my house project. I also bought a coax tester for multi purposes
ОтветитьAwesome video!
Just ordered it from Amazon, and it's only $14.08!
GOOD JOB !!! I JUST ORDERED ONE ON AMAZON ...
Ответитьthanks for the video.
Ответить