Комментарии:
What do they cost?
ОтветитьI have a hard start warm or hot. Cold start 1st in the morning, fine
Ответитьhow much, and where buy order
Ответитьhow much break out box
Ответитьhow to order it
Ответитьdude i have a 03 f-650 cummins 24 valve lost powre at lift pump power wire at pump comes out of pcm bypassed that put on own relay to get power starts but in limp mode for no power at lift pump still how do i get out of limp mode
ОтветитьGreat information!! Thanks for every video because to me all are very informative and at the same time I enjoy every single one of them
ОтветитьAfter a hard wired test my truck starts right up, so I'm looking up for a ECM issue.. so do your own research and look for pin 6 and 7 from vp44 and run a fuse wire straight to the battery and a negative and it's the same with this attachment.. easy
ОтветитьHi Will this also work on a ford transit vp30 pump, I'm having starting issues.
ОтветитьI'm wondering what if the psg computer fails?
ОтветитьSir where i can get this box for starting vp44 directly?
ОтветитьDoes it work for heavy machinery with 24v voltage or only 12v ??
ОтветитьI have 2000 was having throttle body issues. Because it would fluctuate and finally it went dead go dead. Replaced the throttle body sensor and got it to crank it would be running good and then just go dead. It did this about 3 different times. Finally pulled it off got it cranked run like a top for about 9 miles and just fell on its face and died. Haven't been able to get it cranked since. Any info is appreciated.
ОтветитьThank you for this Wade. Very informative for a VP44 tech such as myself.
ОтветитьDumb question, would this work on other equipment with vp44 pumps?
ОтветитьWhere to buy a breakout box? Price?
ОтветитьAnother great video.
ОтветитьI have a prob with my 98 Dodge Ram 2500 5.9 Cummins 24 v it idles great as soon as I hit the throttle it chokes up I replaced the throttle sensor already hope someone could help me out
ОтветитьI have a problem with the jeep Suzuki D-Max, there is no effect on the throttle acceleration of the jeep, the speed is constant
ОтветитьThe longer the truck sits the harder too start... Why???
ОтветитьCan you send me the wiring diagram for this box and the swchears forit
ОтветитьGreat product guys. Where is the best place to get a ECM
ОтветитьMi problema es el ENCENDIDO. Ya solo empujada , de bajada o remolcadas enciende y no esta desforzada no falla en la aceleración, consumo de diésel Normal.
Si pudieran decir comentarios en ESPAÑOL. POR FAVOR.
Omg dude a 1 min video you turn into 20 min
ОтветитьI have an 02 and having issues. It starts and runs fine, hot or cold. I can be idling or driving a d the truck will shut off but if I’m driving it’ll star back by itself. If it’s idling, it’ll die but I have to turn the key to start it. Hooked a reader up to it and it can’t find anything but cycling the key it has p1693. Any ideas??
Ответитьwere to buy
Ответитьhalo .. bisakah anda membantu saya untuk harga sampai ke indonsia ??
ОтветитьThis is nothing more than a "Hotwire test is it not? which will cost you nothing
ОтветитьDoes the VP 44 sense the temperature when it is cooler and compensate with more fuel for starting?
ОтветитьDoes the VP 44 sense a problem with an injector and try to compensate?
ОтветитьSo what caused the tone change When you plugged the box in
ОтветитьHello, the same is used in 12v and 24 v system
ОтветитьHow much is the breakout box?
ОтветитьWhat if the truck won't stay running, just starts and cuts off immediately. Reading 19 lbs of pressure to the vp44.
ОтветитьSo why pressure diesel is very law pressure. What's problem for vp44
Ответитьhallo Clark
will this work on all engines brands with vp 44 to give idlle or less more?
greetings
Sorry if I didn't get this straight - but if the engine starts and runs with the breakout box the pump is okay? Or the pump is not okay?
ОтветитьALL fuel gauges fail?
ОтветитьOkay I have. 2001 Dodge Ram 2500 24v, I have replaced ecm, fass 165, new engine harness, and new injection pump! So my problem is when I unplug the vp44 & run a ground from the injection pump plug in to the battery and it will start right up! If I plug the injection pump back in it will not start!
Ответитьhow can i buy this tools
ОтветитьHey is there any way I can contact you via social media? WhatsApp or etc? Your kindness is greatly appreciated! Thank you
ОтветитьNoticed a belt sqeak at shut off....time to change that belt and idler tension wheel. Cool product...
ОтветитьThis box work with VP30 and where do I buy this box?
Ответитьis this applicable to nissan patrol zd30 y61 vp44 injection pump and how much to avail
ОтветитьMerci selvopler le chima démarrage
ОтветитьHello! how many is this machine?
ОтветитьHave a question don't know if you can answer it in the comments but my 2000 5.9 Cummins 24-valve automatic always starts but takes about 10 seconds if it's sitting overnight or more than a couple hours if the front end is slightly uphill if it's warmed up and downhill starts immediately another problem is when I'm driving and it hits about somewhere around 30 miles an hour it starts lunging but if I give it gas and that corrects it but then I'm going 40 miles in a 30-mile Zone or 45 does the same thing around 45 to 50 and actually does this when it's shifting second and third or third 2/4 th it's when the RPMs go there lowest it l u g s so it's really hard to drive around the city because all of the speed limits are in that area lot of times I just keep the overdrive off but still does it between second and third if I'm just tooling around the city do you have any suggestions thanks I'll also try your website to or maybe some of your other patrons might have some ideas
ОтветитьWould it help me diagnose my 02 24v getting stuck at high rpm then getting dead pedal after going on the highway when its colder out? I t starts fine though. After I turn off and let sit for a minutes and start back up, the rpm settles back down to normal idle.
ОтветитьI am in the beginning phases of learning about the VP-44. I have one in my motorhome. Does any or all of this info transfer to the motorhome applications?
ОтветитьQuick question... I have a 2001 and the fuel pressure port is on the back side of the fuel filter housing. Is this an OK place to ck the pressure? I assume this is pressure before the filter. Or is it after? Thanks for the help!
Ответить